Schneider Electric AP9630, AP9631 LED Descriptions

UPS Network Management Card 2 User’s Guide6

LED Descriptions

Status LED

This LED indicates the status of the NMC.

Link-RX/TX (10/100) LED

This LED indicates the network status of the NMC.

5Reset button Resets the NMC while power remains on.

6Serial configuration port Connects the NMC to a local computer to configure initial network

settings or access the command line interface.

7Link-RX/TX (10/100) LED See “Link-RX/TX (10/100) LED” on page6.

8Status LED See “Status LED” on page6.

Condition Description

Off

One of the following situations exists:

•The NMC is not receiving input power.

•The NMC is not operating properly. It may need to be repaired or replaced. Contact

Customer Support. See “APC Worldwide Customer Support” on page89.

Solid green The NMC has valid TCP/IP settings.

Solid orange A hardware failure has been detected in the NMC. Contact Customer Support. See

“APC Worldwide Customer Support” on page89.

Flashing green The NMC does not have valid TCP/IP settings.1

Flashing orange The NMC is making BOOTP requests.1

Alternately flashing

green and orange If the LED is flashing slowly, the NMC is making DHCP2 requests.1

If the LED is flashing rapidly, the NMC is starting up.

1. If you do not use a BOOTP or DHCP server, see the Networ k Ma nagem ent Ca rd Installatio n Manua l prov ided in

printed format and on the Network Management Card Utility CD in PDF to configure the TCP/IP settings of the

NMC.

2. To use a DHCP server, see “TCP/IP and Communication Settings” on page 54.

Condition Description

Off

One or more of the following situations exist:

•The NMC is not receiving input power.

•The cable that connects the NMC to the network is disconnected or defective.

•The device that connects the NMC to the network is turned off or not operating

correctly.

Off (continued) •The NMC itself is not operating properly. It may need to be repaired or replaced.

Contact Customer Support. See “APC Worldwide Customer Support” on page89.

Solid green The NMC is connected to a network operating at 10 Megabits per second (Mbps).

Solid orange The NMC is connected to a network operating at 100 Mbps.

Item Description

Contents

Main CD . Introduction Product Description IPv4 initial setup IPv6 initial setup Network management features Internal Management Features Access priority for logging on Types of user accounts How to Recover from a Lost Password Front Panel (AP9630) Front Panel (AP9631) LED Descriptions Status LED This LED indicates the network status of the NMC. This LED indicates the status of the NMC. Link-RX/TX (10/100) LED Watchdog Features Network interface watchdog mechanism Resetting the network timer Command Line Interface (CLI) How To Log On Remote access to the command line interface Local access to the command line interface Main Screen Sample main screen Information and status fields Page How to Use the Command Line Interface How to enter commands Command syntax Syntax examples Command Response Codes Command Descriptions ? about alarmcount boot cd cfgshutdn cfgpower console date delete detstatus dir dns eventlog exit format ftp of any unused port from 5001 to 32768 for added security. help ntp ping the network. portspeed prompt quit radius reboot resetToDef snmp, snmpv3 system tcpip tcpip6 uio ups Option Arguments Description upsfwupdate user web xferINI xferStatus Web User Interface Introduction Supported Web browsers How to Log On URL address formats Page Home Page Quick status icons Recent Device Events Tabs, Menus, and Links Monitor and Configure the UPS Overview Page Operating state Quick Status Recent UPS Events Control page UPS option Page Action Definition outlet groups option Configuration Pages What are Outlet Groups? The outlet groups option (including automatic load-shedding) The power settings option The shutdown option UPS without outlet groups: shutdown time UPS WITH outlet groups: shutdown time The general option Force Negotiation: UPS without outlet groups IF THEN Force Negotiation: UPS WITH outlet groups IF THEN The self-test schedule option The firmware update option The PowerChute clients option The sync control option The parallel units option (Smart-UPS VT UPS devices) Diagnostics page Scheduling page (for shutdowns) For both the UPS and outlet group options For the UPS option only: synchronized shutdowns Page Environmental Monitoring Overview Page Temperature and Humidity Page Input Contacts Page Output Relay Page About Page Configuring the Control Policy Configuring an output to respond to an event Configuring the UPS or output to respond to an input alarm Logs Using the Event and Data Logs Event log Data log How to use FTP or SCP to retrieve log files Page Administration: Security Local Users Setting user access Remote Users Authentication Configuring the RADIUS Server Summary of the configuration procedure Configuring a RADIUS server on UNIX with shadow passwords Supported RADIUS servers Inactivity Timeout Administration: Network Features TCP/IP and Communication Settings TCP/IP settings for IPv4 DHCP response options TCP/IP settings for IPv6 Ping Response Port Speed DNS Page Web Path: Path: Administration > Network > Web > options Console Path: Administration > Network > Console > Path: options A Console session means youre using the command line interface, see Command Line Interface (CLI). SNMPv1 SNMPv3 Page FTP Server Administration: Notification Event Actions Types of notification Configuring event actions Active, Automatic, Direct Notification E-mail notification Page SNMP traps SNMP Trap Test Remote Monitoring Service Syslog Page Administration: General Options Identification Set the Date and Time Mode Daylight saving Use an .ini File Event Log, Temperature Units, Language, and Logon Page Color-code event log text Change the default temperature scale Specify the UI language Specify a default logon page Configure Links About the Network Management Card 2 Device IP Configuration Wizard Capabilities, Requirements, and Installation How to use the Wizard to configure TCP/IP settings System requirements Installation How to Export Configuration Settings Retrieving and Exporting the .ini File Summary of the procedure Contents of the .ini file Detailed procedures The Upload Event and Error Messages The event and its error messages Messages in config.ini Errors generated by overridden values Related Topics File Transfers Upgrading Firmware Firmware module files (Network Management Card 2) Firmware File Transfer Methods Using the Firmware Upgrade Utility Use FTP or SCP to upgrade one Network Management Card Use XMODEM to upgrade one NMC Use a USB drive to transfer and upgrade the files (AP9631 only) Upgrading the firmware on multiple Network Management Cards Verifying Upgrades Verify the success or failure of the transfer Last Transfer Result codes Verify the version numbers of installed firmware Adding and Changing Language Packs Troubleshooting Network Management Card Access Problems SNMP Issues Synchronization Problems Appendix A: List of Supported CLI Commands Page Two-Year Factory Warranty Terms of warranty Non-transferable warranty Exclusions Page Radio Frequency Interference Page 3/2012 990-3402D-001 APC Worldwide Customer Support