Grease Bearings | SEAL 6500 specs

Grease Bearings

P E R I O D I C M A I N T E N A N C E S H E E T

Chain Tension	Drain Water
Adjustment/Oil Chain**	(Air Filter)***

Safety Check After Servicing

NOTE: Enter dates of service and initials of service personnel.

We recommend that you make a photocopy of this page, tape it to the inside of the cabinet door and use this to record dates that authorized safety or maintenance personnel perform these laminator maintenance procedures.

Proper maintenance of your laminator ensures receiving many years of profit from your investment.

Use only replacement parts specified by SEAL Graphics.

**Use lightweight household oil to oil the chain approximately every three months.

***Drain the air filter approximately every six months to prevent moisture damage to the air cylinders.

Call SEAL Graphics Technical Service for assistance (see the rear cover).

33

Image 33

SEAL 6500 owner manual Grease Bearings, Chain Tension Drain Water Adjustment/Oil Chain Air Filter

Contents

Image 6500 Laminator Page T R O D U C T I O N Statement of Intended USE E C T R I C a L S P E C I F I C AT I O N S Connecting Your Laminator R K S PA C E R E Q U I R E M E N T S Media Power Supply Ambient TemperatureRelative Humidity Water and Moisture PA C K I N G , S E T- U P a N D I N S TA L L AT I O N Accessories Included Leveling Your Laminator Unpacking Your Laminator Rotating Parts Risk of Injury Servicing and Replacement PartsHot Surface Risk of Injury on Contact Electrical Parts Danger of being injured by electricity Door Interlock F E T Y F E AT U R E S M I N AT O R F E AT U R E S Features Front Control Panel O N T C O N T R O L PA N E L Back Control Panel C K C O N T R O L PA N E L AIR Pressure Gauge AIR Regulator KnobU T C H C O N T R O L PA N E L Reverse Roller Direction Switch Speed Adjustment KnobMotor Stop Switch Forward Roller Direction Switch Check the Motor and Foot Switches Check the Main PowerCheck the Emergency Stop Buttons Check the Heater Controls HOW to SET the Shim Wheels Temperature SettingsShim Wheel Settings T- U P a N D O P E R AT I O N Loading a Roll of Material Unwind shaft cord adjustment Pivoting Roll Easel Bracket Down Pivoting Table USE for Webbing Cooling System Setting the Unwind Brake TensionTo remove the cooling tube from the bottom location To insert the cooling tube in the top location Foot Switch Operation AUTO-RUN OperationRotation of the Rollers will Stop When Using the Roll Easel Attachment Using the Print Guide TableBasic Steps to Feeding Images E D I N G I M a G E S B B I N G F I L M S W I T H O U T a R E L E a S E L I N E R You are now ready to feed images B B I N G F I L M S W I T H a R E L E a S E L I N E R YOU are NOW Ready to Feed Images Films Webbing Settings Webbing for Decaling Pressure-sensitive films Media Ink Jet, Electrostatic, and Photographic U N T I N G To Mount Decals Onto a Substrate Front C a P S U L AT I N G E C O AT I N G B O a R D S Preparation Webbing for Vinyl Transfer Media Electrostatic Back Control Panel Settings Front Control Panel SettingsMotor Control Panel Settings Webbing Settings Cleaning the Rollers Cleaning the LaminatorGreasing the Bearings E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O R Chain Tension Drain Water Adjustment/Oil Chain Air Filter Grease BearingsR I O D I C M a I N T E N a N C E S H E E T Technical Service Problem Solution LED PA R E PA R T S L I S T Process MechanicalElectrical Order Codes M I T E D W a R R a N T Y