Ambient Temperature, Relative Humidity, Surroundings | SEAL 6500

E N V I R O N M E N T C O N D I T I O N S

The following environmental conditions are ideal for the best operation of the laminator.

AMBIENT TEMPERATURE

The best temperature for the SEAL Image 6500 is between 50°F and 86°F (10°C and 30°C).

Do not expose the laminator to direct sunlight as output quality may be affected.

RELATIVE HUMIDITY

For best results, the ambient relative humidity for the SEAL Image 6500 should be between 70-90% non-con- densing. Too much humidity will affect the prints being laminated causing problems with film adhesion.

WATER AND MOISTURE

If the laminator is installed in a damp room or near water, the electrical power supply must be in accordance with the standards prevailing in the country concerned.

SURROUNDINGS

Install the laminator in surroundings that are as clean and dust-free as possible in order to obtain the highest quality output.

The background dust level must not exceed that found in a typical office/computer room environment.

The materials that are used on this laminator can have an electrostatic charge and will attract dust, adversely affect- ing the output.

POWER SUPPLY

Connect the laminator in accordance with the details given on the identification plate attached to the rear of the laminator. Refer also to the Technical Specifications page for more information.

6

Image 6

SEAL 6500 owner manual Ambient Temperature, Relative Humidity, Water and Moisture, Surroundings, Power Supply

Contents

Image 6500 Laminator Page Statement of Intended USE T R O D U C T I O N Connecting Your Laminator E C T R I C a L S P E C I F I C AT I O N S Media R K S PA C E R E Q U I R E M E N T S Relative Humidity Ambient TemperaturePower Supply Water and Moisture Accessories Included PA C K I N G , S E T- U P a N D I N S TA L L AT I O N Unpacking Your Laminator Leveling Your Laminator Hot Surface Risk of Injury on Contact Servicing and Replacement PartsRotating Parts Risk of Injury Electrical Parts Danger of being injured by electricity F E T Y F E AT U R E S Door Interlock Features M I N AT O R F E AT U R E S O N T C O N T R O L PA N E L Front Control Panel C K C O N T R O L PA N E L Back Control Panel AIR Pressure Gauge AIR Regulator KnobU T C H C O N T R O L PA N E L Motor Stop Switch Speed Adjustment KnobReverse Roller Direction Switch Forward Roller Direction Switch Check the Emergency Stop Buttons Check the Main PowerCheck the Motor and Foot Switches Check the Heater Controls Shim Wheel Settings Temperature SettingsHOW to SET the Shim Wheels T- U P a N D O P E R AT I O N Unwind shaft cord adjustment Loading a Roll of Material Pivoting Table USE for Webbing Pivoting Roll Easel Bracket Down To remove the cooling tube from the bottom location Setting the Unwind Brake TensionCooling System To insert the cooling tube in the top location Foot Switch Operation AUTO-RUN OperationRotation of the Rollers will Stop When Basic Steps to Feeding Images Using the Print Guide TableUsing the Roll Easel Attachment E D I N G I M a G E S You are now ready to feed images B B I N G F I L M S W I T H O U T a R E L E a S E L I N E R YOU are NOW Ready to Feed Images B B I N G F I L M S W I T H a R E L E a S E L I N E R Webbing Settings Films Media Ink Jet, Electrostatic, and Photographic Webbing for Decaling Pressure-sensitive films To Mount Decals Onto a Substrate U N T I N G C a P S U L AT I N G Front Preparation E C O AT I N G B O a R D S Media Electrostatic Webbing for Vinyl Transfer Motor Control Panel Settings Front Control Panel SettingsBack Control Panel Settings Webbing Settings Greasing the Bearings Cleaning the LaminatorCleaning the Rollers E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O R Chain Tension Drain Water Adjustment/Oil Chain Air Filter Grease BearingsR I O D I C M a I N T E N a N C E S H E E T Problem Solution Technical Service LED PA R E PA R T S L I S T Electrical MechanicalProcess Order Codes M I T E D W a R R a N T Y