Pivoting Table USE for Webbing | SEAL 6500 guide

S E T- U P A N D O P E R AT I O N

PIVOTING TABLE USE FOR WEBBING

•First, remove the roll easel shaft from its brackets and set aside.

•Pull out both retaining plungers of the roll easel brackets and pivot the brackets down and forward as shown in Figure 12.

•Pull the film up and place it over the top roller.

•Reposition the table by lifting the outer edge upwards and pivot in towards the roller (Figure 14).

•With the table resting on the table bracket standoffs, lift the outer edge of the table and push the table in towards the roller (see Figure 15). The non-locking retaining plunger will catch automatically.

•Moving to the right-hand side of the table release the locking retaining plunger so it locks in place.

•The table operation is the same front and rear.

Figure 12. Pivoting Roll Easel Bracket Down

•Remove the top and bottom wind-up idlers for easy webbing and set them aside.

•On the right-hand side of the table, pull out the locking retaining plunger and turn sideways to lock with plunger recessed (see Figure 13).

•Move to the left side and pull out the non-locking retaining plunger on the left-hand side of the table.

•Allow the table brackets to slide outwards and down.

•Grasp the front edge of the table and, lifting up, pivot the table towards you, away from the rollers (see Figure 13).

•Reach through the opening between the table and rollers and pull the bottom film up and pass it behind the bot- tom idler.

Figure 13.	Figure 14
Releasing Retaining Plunger	Pivoting Table Up

Figure 15.

Pivoting Table Forwards

19

Image 19

SEAL 6500 owner manual Pivoting Table USE for Webbing, Pivoting Roll Easel Bracket Down

Contents

Image 6500 Laminator Page T R O D U C T I O N Statement of Intended USE E C T R I C a L S P E C I F I C AT I O N S Connecting Your Laminator R K S PA C E R E Q U I R E M E N T S Media Water and Moisture Ambient TemperaturePower Supply Relative Humidity PA C K I N G , S E T- U P a N D I N S TA L L AT I O N Accessories Included Leveling Your Laminator Unpacking Your Laminator Electrical Parts Danger of being injured by electricity Servicing and Replacement PartsRotating Parts Risk of Injury Hot Surface Risk of Injury on Contact Door Interlock F E T Y F E AT U R E S M I N AT O R F E AT U R E S Features Front Control Panel O N T C O N T R O L PA N E L Back Control Panel C K C O N T R O L PA N E L AIR Regulator Knob AIR Pressure GaugeU T C H C O N T R O L PA N E L Forward Roller Direction Switch Speed Adjustment KnobReverse Roller Direction Switch Motor Stop Switch Check the Heater Controls Check the Main PowerCheck the Motor and Foot Switches Check the Emergency Stop Buttons T- U P a N D O P E R AT I O N Temperature SettingsHOW to SET the Shim Wheels Shim Wheel Settings Loading a Roll of Material Unwind shaft cord adjustment Pivoting Roll Easel Bracket Down Pivoting Table USE for Webbing To insert the cooling tube in the top location Setting the Unwind Brake TensionCooling System To remove the cooling tube from the bottom location AUTO-RUN Operation Foot Switch OperationRotation of the Rollers will Stop When E D I N G I M a G E S Using the Print Guide TableUsing the Roll Easel Attachment Basic Steps to Feeding Images B B I N G F I L M S W I T H O U T a R E L E a S E L I N E R You are now ready to feed images B B I N G F I L M S W I T H a R E L E a S E L I N E R YOU are NOW Ready to Feed Images Films Webbing Settings Webbing for Decaling Pressure-sensitive films Media Ink Jet, Electrostatic, and Photographic U N T I N G To Mount Decals Onto a Substrate Front C a P S U L AT I N G E C O AT I N G B O a R D S Preparation Webbing for Vinyl Transfer Media Electrostatic Webbing Settings Front Control Panel SettingsBack Control Panel Settings Motor Control Panel Settings E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O R Cleaning the LaminatorCleaning the Rollers Greasing the Bearings Grease Bearings Chain Tension Drain Water Adjustment/Oil Chain Air FilterR I O D I C M a I N T E N a N C E S H E E T Technical Service Problem Solution LED PA R E PA R T S L I S T Order Codes MechanicalProcess Electrical M I T E D W a R R a N T Y