![](/images/new-backgrounds/1283396/2833965x1.webp)
ASSEMBLING AND ADJUSTING YOUR SAW
10 9
1
2
4 7
S
Figure 1
UNPACKING AND CHECKING CONTENTS
This Craftsman 10olnch Radial Saw is shipped complete in one carton. In order to prevent damage during shipment and facilitate packaging, certain items are removed at the factory and must be assembled when received by the pur- chaser. These "loose" items are listed below and should be accounted for before discarding any packing materials.
Key | No. |
|
|
|
|
(Fig. | 1) |
| Item | Name | Qty. |
| 1 | Table | Support, | 1 | |
| 2 | Table, | Front | 1 | |
3 | Table, | Rear | ...................... | 1 | |
| 4 | Table, | Spacer | 1 | |
| 5 | Fence, | Rip | ....................... | 1 |
| 6 | Table Support, | 1 | ||
| 7 | Owner's Manual | 1 | ||
| 8 | Unpacking | Instructions | 1 | |
| 9 | Shaft Wrench | 1 | ||
10 | Arbor | Wrench | 1 |
11Pack Assm., Loose Parts (containing the following):
Wrench, | 1/8" | ............ |
|
| 1 | ||
Wrench, | ........... |
|
| 1 | |||
Wrench, | ............ |
|
| 1 | |||
Wrench, | 5/16" | ........... |
|
| 1 | ||
Washer, | Plain, | 11/32 | x 7/8 | x1/16 | _/ | 4 | |
Lockwasher, 5/16x.125 | x.078" . . . | 4 | |||||
Screw, Hex. Hd. | x 3/4 'I ... |
| 4 | ||||
Screw, M. Pan. SI., | x | 1" .... |
| 6 | |||
Washer, | Plain, | 17/64 | x 5/8 | x 1/32 | p_ | 7 | |
Lockwasher, Steel, 1/4 | x .109 | x .062" | 6 | ||||
Nut, Hex., |
| x 3/16" .. | 6 | ||||
Nut, Tee | ...................... |
|
|
|
| 1 |
Key | No. |
|
|
|
|
|
(Fig. | 1) | Item | Name | Qty. | ||
|
| Screw, | M. Pan. SI., | 1 | ||
|
| Screw, | SI. Cup | Pt., Set, | 1 | |
|
| Screw, Type A, Pan Hd., Sl., |
| |||
|
| No. | 10x5/8" | ................ | 4 | |
|
| Screw, Type 23, Pan Hd., Sl., |
| |||
|
| No. | 2 | |||
|
| Nut, | 1 | |||
|
| Clamp, |
| Table | .................. | 2 |
|
| Switch | Key | 2 | ||
|
| Shoe, | Carriage | Lock | 1 | |
|
| Knob, | Carriage | Lock | 1 | |
|
| Indicator, | Rip | .................. | 1 | |
|
| Nut, | Twin | 1 | ||
|
| Bracket, | Rear | Table Support | 2 |
POWER SUPPLY AND MOTOR DATA
MOTOR SPECIFICATIONS
The
Voltage | 120 |
Amperes | 12.5 |
Hertz | 60 |
Phase | Single |
RPM | 3450 |
Rotation (viewing saw blade end) Clockwise
CAUTION: This motor is wired for 120 volt operation. Connect to 15 ampere branch circuit and use a 15 ampere
3