No.

 

 

 

Parts

 

 

Note

 

 

 

 

 

 

 

Code

Signal name

Name

Type

Function/operation

Active condition

 

 

 

 

 

 

 

 

 

1

PE SENSOR

PEMP IN

Paper empty

Photo

Detects paper on the paper tray.

LOW (0V) when

 

 

 

 

detector

transmission

 

paper is detected.

 

 

 

 

 

sensor

 

 

 

 

 

 

 

 

 

 

 

2

 

 

Paper guide

 

Adjust the paper width.

 

 

 

 

 

 

 

 

 

 

3

 

 

Paper feed tray

 

Sets the print paper. (Capacity:

 

 

 

 

 

 

 

XXX sheets)

 

 

 

 

 

 

 

 

 

 

4

 

 

Paper release

 

Put this lever straight to set

 

 

 

 

 

lever

 

paper to release paper feed. Put

 

 

 

 

 

 

 

this lever down to enable paper

 

 

 

 

 

 

 

feed.

 

 

 

 

 

 

 

 

 

 

5

PUS

PUS

Paper feed clutch

 

Controls (on/off) the main motor

 

 

 

 

 

solenoid

 

drive for the paper feed roller.

 

 

 

 

 

 

 

 

 

 

6

 

 

Paper feed

 

When the paper feed lever is put

 

 

 

 

 

release lever

 

straight, this lever releases

 

 

 

 

 

 

 

paper feed solenoid drive. This

 

 

 

 

 

 

 

partially reduces stress to the

 

 

 

 

 

 

 

paper feed roller clutch in

 

 

 

 

 

 

 

removing paper.

 

 

 

 

 

 

 

 

 

 

7

PIN SENSOR

PIN

Paper in detector

Photo

Detects whether the fed paper is

LOW (0V) when

 

 

 

 

 

transmission

transported to the transfer

paper is detected.

 

 

 

 

 

sensor

position or not. By the timing of

 

 

 

 

 

 

 

this detector signal, the relative

 

 

 

 

 

 

 

positions of paper and print

 

 

 

 

 

 

 

image are controlled.

 

 

 

 

 

 

 

 

 

 

8

 

 

Paper feed roller

 

Feeds paper.

 

 

 

 

 

 

 

 

 

 

9

PAPER SIZE

PAPER SIZE

Paper width

Mechanical

Detects the paper width. This

LOW (0V) when

 

 

SW

IN

detector

switch (Micro

signal controls the laser beam

the max. width is

 

 

 

 

 

switch)

radiation area.

detected.

 

 

 

 

 

 

 

 

 

10

 

 

Paper pressure

 

Presses paper onto the paper

 

 

 

 

 

plate

 

feed roller.

 

 

 

 

 

 

 

 

 

 

11

 

 

Paper pressure

 

Presses paper onto the paper

 

 

 

 

 

spring

 

feed roller.

 

 

 

 

 

 

 

 

 

 

12

 

 

Paper separator

 

Separates paper in paper feed

 

 

 

 

 

 

 

operation.

 

 

 

 

 

 

 

 

 

 

13

 

 

Paper feed clutch

Mechanical

Controls ON/OFF of the paper

 

 

 

 

 

 

spring type

feed roller. (The paper feed roller

 

 

 

 

 

 

clutch

is driven by the paper feed clutch

 

 

 

 

 

 

 

solenoid and the main motor.

 

 

 

 

 

 

 

 

 

 

14

 

 

Paper feed clutch

 

Driven by the paper feed clutch

 

 

 

 

 

lever

 

solenoid to control ON/OFF of

 

 

 

 

 

 

 

the paper feed clutch. Prevents

 

 

 

 

 

 

 

against reverse rotation of the

 

 

 

 

 

 

 

paper feed roller.

 

 

 

 

 

 

 

 

 

 

15

 

 

Paper feed clutch

 

Links the paper feed roller and

 

 

 

 

 

joint

 

the paper feed roller clutch.

 

 

 

 

 

 

 

 

 

 

16

 

 

Paper feed clutch

 

Controls ON/OFF of the paper

 

 

 

 

 

sleeve

 

feed roller. (The paper feed roller

 

 

 

 

 

 

 

is driven by the paper feed clutch

 

 

 

 

 

 

 

solenoid and the main motor.)

 

 

 

 

 

 

 

 

 

 

17

 

 

Paper feed clutch

 

Transmits the paper feed clutch

 

 

 

 

 

spring

 

rotation to the paper feed clutch

 

 

 

 

 

 

 

sleeve.

 

 

 

 

 

 

 

 

 

 

18

 

 

Paper feed clutch

 

Transmits the main motor power

 

 

 

 

 

gear

 

to the paper reed roller.

 

 

 

 

 

 

 

 

 

 

19

 

 

Paper separater

 

Applies a proper pressure to the

 

 

 

 

 

spring

 

paper separater.

 

 

 

 

 

 

 

 

 

 

1 – 6

Page 7
Image 7
Sharp Digital Copier, AL-840, AL-800 service manual PE Sensor Pemp, Pus, PIN Sensor, Paper Size