STATUS INDICATORS
When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the relevant page.
Be sure to use only genuine SHARP parts and supplies.
| Indication |
| Cause and remedy | Page |
| Developer | Steadily | Developer is required. contact your authorised |
|
| replacement required | 56 | ||
| lit | service representative. | ||
| indicator |
|
|
|
| Toner cartridge | Steadily | Replacement of Toner cartridge will be needed soon. | 45 |
| lit | Prepare a new cartridge. | ||
| replacement required |
| ||
|
| Toner cartridge must be replaced. Replace it with a |
| |
| indicator | Blinking | 45 | |
| new one. | |||
|
|
|
| |
|
|
| A misfeed has occurred. Remove the misfed paper | 52 |
| Misfeed indicator | Blinking | referring to the description of "MISFEED REMOVAL". | |
|
| |||
|
|
| The lower side cover may be open. If so, close it. | 55 |
| Maintenance | Steadily | Service by an authorised SHARP service technician | 56 |
| indicator | lit | is required. | |
|
| |||
|
|
|
|
|
| SPF misfeed |
| An original misfeed has occurred in the SPF. Remove | 55 |
| Blinking | the misfed originals referring to the description of "E: | ||
| indicator | |||
|
| Misfeed in the SPF". |
| |
|
|
|
| |
|
|
|
|
|
|
|
| The unit is in the preheat mode. Press any key to | 42 |
|
|
| cancel the preheat mode. | |
| Power save indicator is steadily |
| ||
| The unit is in the auto power |
| ||
| lit. |
| start ( ) key to cancel the auto power | 42 |
|
|
| mode. |
|
| The paper tray indicator is | The paper tray is not installed properly. Push the tray | – | |
| blinking. |
| into the unit securely. | |
|
|
| ||
|
|
|
|
|
|
|
| The toner cartridge is not installed. Check if the |
|
| "CH" is blinking in the display. | cartridge is installed. If "CH" is blinking even if a | – | |
| cartridge is installed properly, contact your SHARP | |||
|
|
|
| |
|
|
| service centre immediately. |
|
|
|
| Side cover is open. Close the side cover securely by |
|
| "CH" is steadily lit in the display. | pressing the round projections near the side cover | – | |
|
|
| open button. |
|
|
|
| The paper tray or | 8, 10 |
|
|
| Load paper. | |
|
|
|
| |
|
|
| A misfeed has occurred in the paper tray, single |
|
| "P" is blinking in the display. | bypass or | 52 | |
|
|
| paper. |
|
|
|
| Paper tray is not securely installed. Push the tray in | – |
|
|
| securely. | |
|
|
|
| |
| A letter and a number appear | The scan head locking switch is locked. Unlock the |
| |
| scan head locking switch and turn the power switch | 57 | ||
| alternately. |
| ||
|
| off/on. |
| |
|
|
|
| |
|
|
|
|
|
|
|
| The unit will not function. Turn the power switch off |
|
| A letter and a number appear | and then switch it on, and if there is again an error, | – | |
| alternately. |
| remove the power cord from the outlet, and contact | |
|
|
| ||
|
|
| your authorized service representative. |
|
|
|
|
|
|
|
|
| The unit will not function. Turn the power switch off |
|
| A letter and a number appear | and then switch it on, or when the side cover is |
| |
| opened and then closed ; and if there is again an | – | ||
| alternately. |
| ||
|
| error, check whether or not you forgot to remove the |
| |
|
|
|
| |
|
|
| bundling tape on the cartridge. |
|
7
51
