Removing and Installing the Lamp Unit | Sharp PGLW2000, PG-LW2000

Removing and Installing the Lamp Unit

Warning!

•Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Optional	Lamp unit
accessory	AN-LX20LP
	AN-LX20LP

Info

•Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1 Press STANDBY/ON on the projector or STANDBY on the remote control to put the projector into Standby mode.

2 Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3Remove the lamp unit cover.

•Loosen the user service screw (1) that secures the lamp unit cover. Slide the lamp

unit cover in the direction of the arrow and then lift it up (2).

STANDBY/ON button

AC socket

User service screw (for lamp unit cover)

Appendix

57

Image 59

Sharp PGLW2000, PG-LW2000 Removing and Installing the Lamp Unit, Remove the lamp unit cover, STANDBY/ON button AC socket

Contents

PG-LW2000 Model No Serial No Void the users authority to operate this equipment See bottom of projector Information Product Disposal Optional accessories Accessories Contents Viewing Stereoscopic 3D Images Reference Power-Cord Protection CleaningPower Sources Accessories Overloading Damage Requiring ServiceReplacement Parts Safety Check Do not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Other connected equipment Using the projector in other countriesTemperature monitor function 15 16 Part Names and Functions Rear View Terminals Part Names and Functions Usable Range Remote control signal transmittersInserting the Batteries Easy Start Setup and Projection Input list Correcting trapezoidal distortion using Keystone CorrectionOn the remote control Standard Setup Front Projection Setting Up the ProjectorVideo Setup Setting Up the Projector Screen Lens center Signal Input Normal ModeScreen Size and Projection Distance Ceiling-Mount Setup Projection PRJ Mode You may need other cables or connectors not listed below Connecting the Projector to Other Equipment Connecting the Projector to Other Equipment AC socket To AC outlet Power cord supplied Connecting the Power Cord Controlling the Projector by a Computer RS-232C Terminal D-sub 9 pin male connector Turning the Projector On Power indicator Lamp indicatorTurning the Projector On/Off Image Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Press Enter to exit the Setup Guide screen Rotate the zoom ring to enlarge or shrink the picture size Adjusting the HeightAdjusting the Picture Size Use the rear adjustment foot to make the projector level Press Keystone Correcting Trapezoidal Distortion VOL +/- Volume buttons Input buttons AV Mute button Buttons Switching the Input ModeAdjusting the Volume Button Resize ModePress Resize About Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot Function Displaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving Image Picture menu Menu Items Main menu Projector adjustment PRJ-ADJ1/2 menu Example Using the Menu ScreenMenu Selections Quick Start Menu Press Menu Following items can be conﬁgured on the Quick Start Menu Example Adjusting BrightQuick Start Menu Menu Selections Complete Menu Press Enter To adjust the projected image while watching itPress P or R and select Bright to adjust Press O or Q to adjust the item selected Menu operation n Picture Adjustment Picture MenuSelecting the Picture Mode Adjusting Hue, Saturation, or Value Adjusting the ImageAdjusting the Color Temperature Adjusting the Colors Reducing Image Noise DNR Selecting the Film ModeEco+Quiet Signal Type Setting Signal Adjustment SIG-ADJ MenuResolution Setting When reproducing Ntsc signals in PAL video equipment Setting the Video SystemSetting the Video Setup Checking the Input Signal Keystone Correction Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Adjusting the Image Position For Americas only Setting the OverscanSetting the On-screen Display Closed Caption Selecting the Wall Color Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected Images Fan Mode Setting Auto Sync Auto Sync AdjustmentAuto Power Off Function Speaker Setting Enter the same keycode in Re- conﬁrm To cancel the keycode that you have already setWhen the System Lock is set System Lock Function Select On, then press Enter Adjusting the Projector Function PRJ-ADJ1/2 MenuKeylock Function Taking the Keylock Off Selecting the Quick Start Menu Setting the Function Button OperationStandby Mode Returning to the Default Settings Viewing Stereoscopic 3D Images Precautions on Viewing Stereoscopic 3D Images Appendix Shutter glasses control light signalInformation on the 3D Projection Function Ending 3D projection Using 3D Viewing ModeProjecting 3D images Cleaning the projector Maintenance About the temperature warning indicator Maintenance Indicators Abnormally high Are high Lower than 95F +35ºC Replacing the Lamp Regarding the LampLamp STANDBY/ON button AC socket Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer Basic format RS-232C Speciﬁcations and CommandsComputer control Communication conditions Computer Projector Commands RGB PAL CC1 Computer Compatibility Chart DTV 19-22 Troubleshooting 53, 54 Problem Check Sharp Electronics France For Sharp Assistance Speciﬁcations Units inches mm Dimensions Index