Sharp PG-LW3000, PG-LW3500, PG-LX3000, PG-LX3500, PGXL3500 63

Maintenance Indicators

■■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.

■■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter Standby mode. After the projector has entered Standby mode, follow the procedures given below.

Top View Temperature warning indicator

Lamp indicator

Power indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising,

“” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. When you find the temperature warning indicator blinking, be sure to perform the measures described on page 63.

About the lamp indicator

■■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter Standby mode. At this time, the lamp indicator will illuminate in red.

■■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.

Indicators on the Projector

Power indicator	Red on	Normal (Standby)
	Green on	Normal (Power on)
	Red blinks	Abnormal (See page 62.)
	Green blinks	Normal (Cooling)
Lamp indicator	Green on	Normal
	Green blinks	The lamp is warming up.
	Red on	The lamp is shut down abnormally or requires to be
		changed. (See page 62.)
Temperature	Off	Normal
warning indicator
warning indicator	Red on/Red blinks	The internal temperature is abnormally high. (See page 62.)

Appendix

61

Contents

MODEL Model No.: Serial No.: ENGLISH INFORMATION PRODUCT DISPOSAL Caution Concerning Lamp Replacement Caution Supplied accessories Preparing Introduction Easy Start Setup Connections Reference CAUTION: Page Observe the following safeguards when setting up your projector Info Page Page Page Inserting the Batteries Caution Usable Range Setup and Projection 1. Place the projector facing a wall or a screen 3. Turn the projector on 6. Select the Input mode 5. Correct trapezoidal distortion 4. Adjust the projected image with the Setup Guide 7.Turn the computer on 8.Turn the power off Video Setup Setting Up the Projector Standard Setup (Front Projection) Indication of the Projection Image Size and Projection Distance [PG-LW3000/PG-LW3500] Screen Size and Projection Distance Screen Size and Projection Distance (Continued) Projection (PRJ) Mode aCeiling-MountSetup Terminals on the Projector Connecting the Projector to Other Equipment (Continued) Page Page Page Turning the Projector On Turning the Power Off (Putting the Projector into Standby Mode) Basic Operation About the Setup Guide Adjusting the Projected Image 1 Adjusting the Focus 2 Adjusting the Height 3 Adjusting the Picture Size Correcting Trapezoidal Distortion Switching the Input Mode Adjusting the Volume Displaying the Black Screen and Turning Off the Sound Temporarily Resize Mode About Copyrights Page Page Displaying the Pointer Displaying and Setting the Break Timer Using the Spot Function Switching the Eco+Quiet Mode Auto Sync (Auto Sync Adjustment) Freezing a Moving Image Selecting the Picture Mode Displaying an Enlarged Portion of an Image Page Page Page Menu Selections (Quick Start Menu) Quick Start Menu To adjust the projected image while watching it 1Selecting the Picture Mode 2Adjusting the Image 3Adjusting the Color Temperature 4Adjusting the Colors 5Selecting the Film Mode 7Eco+Quiet 6Reducing Image Noise (DNR) 2Resolution Setting 3Signal Type Setting 5Setting the Video System 6Setting the Video Setup 7Checking the Input Signal 1Setting the Resize Mode 3Keystone Correction 2Adjusting the Image Position 4Setting the Overscan 5Setting the On-screenDisplay 6Closed Caption 7Selecting the Background Image 8Selecting the Setup Guide 9Reversing/Inverting Projected Images 0Selecting the Wall Color 1Auto Sync (Auto Sync Adjustment) 2Auto Power Off Function 3Auto Restart Function 4Speaker Setting 5Fan Mode Setting 6 System Lock Function 7Keylock Function 8Selecting the Quick Start Menu 9COMPUTER2 Select 0Setting the FUNCTION Button Operation STANDBY Mode STANDBY Audio Out DLP® LinkTM DLP® LinkTM Invert Setting Up the Projector Network Environment (“Network” Menu) 1 Setting a Password 2DHCP Client Setting 3TCP/IP Setting 4Returning to Default Settings (Network) 5Restart Network Function 6Confirming the Projector Information Precautions on Viewing Stereoscopic 3D Images WARNING Information on the 3D Projection Function Using 3D Viewing Mode Warning Projecting 3D images Ending 3D projection Page Page Page Lamp Caution Concerning the Lamp Replacing the Lamp Removing and Installing the Lamp Unit Resetting the Lamp Timer Page Page Page Page Page Page Page Units: inches (mm)