Removing and Installing the Lamp Unit, Lamp unit | Sharp XR-50S

Removing and Installing the Lamp Unit

Warning!

•Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Optional	Lamp unit
accessory	AN-D350LP
	AN-D350LP

Info

•Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1Press STANDBY/ON on the projector or STANDBY on the remote control to put the projector into Standby mode.

2 Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3 Remove the lamp unit cover.

•Close the lens shutter and turn the

projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

STANDBY/ON button

AC socket

User service screw (for lamp unit cover)

Appendix

57

Image 61

Sharp XR-50S Removing and Installing the Lamp Unit, Remove the lamp unit cover, Lamp unit, STANDBY/ON button AC socket

Contents

XR-55X XR-50S Model No Serial No Iii Page Void the users authority to operate this equipment IntroductionENGLISH Sharp Plaza, Mahwah, New Jersey TEL 1-800-BE-SHARP Information For Future Reference Using the Menu Screen Contents Reference Adjusting the Projector Function PRJ-ADJ1/2 Menu Power Sources CleaningAccessories Power-Cord Protection Replacement Parts Damage Requiring ServiceSafety Check Overloading Rest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Page Optional accessories Accessories Front View Part Names and Functions Rear View Terminals Picture Mode button Break Timer buttonCLICK/EFFECT button 34 For displaying the break time Inserting the Batteries Remote control signal transmittersUsable Range Easy Start Setup and Projection On the remote Control Turn the computer on Turn the power off Setting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Signal Input 169 Mode Signal Input Normal ModeScreen Size and Projection Distance Screen Lens center Ceiling-Mount Setup Projection PRJ Mode Terminals on the Projector Connecting the Projector to Other Equipment Connecting the Projector to Other Equipment Monitor OUT AC socket Power cord To AC outlet supplied Connecting the Power CordControlling the Projector by a Computer Turning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On Adjusting the Projected Image Adjusting the Focus About the Setup GuidePress Enter to exit the Setup Guide screen Image Projection Adjusting the Picture Size Adjusting the HeightUse the rear adjustment foot to make the projector level Make small adjustments Height Adjust lever On-screen display Keystone Correction mode Adjustment buttons P/R/O/Q Return button Keystone buttonCorrecting Trapezoidal Distortion Press Keystone Adjusting the Volume Switching the Input ModeInput buttons AV Mute button VOL +/- Volume buttons Buttons Press Resize Resize Mode About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet Mode Selecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an Image When moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clicking Picture menu Menu Items COMPUTER/COMPONENT Projector adjustment PRJ-ADJ1/2 menu Menu Selections Quick Start Menu Using the Menu ScreenPress Menu Example Quick Start Menu Example Adjusting BrightMenu Selections Complete Menu Following items can be conﬁgured on the Quick Start Menu Image while watching it To adjust the projected Selecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting the Color Temperature Adjusting the ImageAdjusting the Colors Adjusting Hue, Saturation, or Value Eco+Quiet Selecting the Film ModeReducing Image Noise DNR Signal Type Setting Signal Adjustment SIG-ADJ MenuResolution Setting When reproducing Ntsc signals in PAL video equipment Setting the Video Setup Setting the Resize Mode Adjusting the Projected Image SCR-ADJ MenuAdjusting the Image Position Keystone Correction Setting the On-screen Display Setting the OverscanClosed Caption For Americas only Selecting the Background Image Selecting the Setup GuideReversing/Inverting Projected Images Selecting the Wall Color Auto Power Off Function Auto Sync Auto Sync AdjustmentSpeaker Setting Auto Restart Function Fan Mode Setting Adjusting the Projector Function PRJ-ADJ1/2 MenuSystem Lock Function Keylock Function Setting the Function Button OperationSelecting the Quick Start Menu Select On, then press Enter Checking the Lamp Life Status Standby Mode Cleaning the projector Maintenance About the temperature warning indicator Maintenance Indicators Red on Abnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitLamp unit STANDBY/ON button AC socket Resetting the Lamp Timer COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Connecting Pin Assignments USB Terminal Type B USB connector Computer control RS-232C Speciﬁcations and CommandsCommunication conditions Basic format Compuer Projector Commands RGB PAL CC1 Computer Computer Compatibility Chart 21-24 Troubleshooting 53, 54 For Sharp Assistance Speciﬁcations Dimensions Index Kensington Security Standard connector ·················13 Appendix