Maintenance Indicators
■The warning lights on the projector indicate problems inside the projector.
■If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.
About the lamp indicator
TEMP.
LAMP
POWER
TEMPERATURE | LAMP | POWER |
WARNING | indicator | indicator |
indicator |
|
|
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the
setting location, “
” will
illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the temperature warning indicator will blink, the cooling fan will run for a further 90 seconds, and then the projector will enter the standby mode. After
“
” appears, be sure to perform the following measures.
■The lamp life becomes 0%, when used for approximately 4,000 hours with “Eco mode” or when used for approximately 3,000 hours with “Standard mode” (see page 53).
■When the remaining lamp life becomes
5% or less, “
” (yellow) will be displayed on the screen. When the percentage be-
comes 0%, “
” will change to “
” (red), the lamp will automatically turn off and then the projector will automatically en- ter the standby mode. At this time, the lamp indicator will illuminate in red.
■If you try to turn on the projector a fourth time without replacing the lamp, the pro- jector will not turn on.
| Maintenance indicator | Condition | Problem | Possible Solution | ||||
|
|
|
| |||||
|
| Normal | Abnormal | |||||
|
|
|
|
|
|
| ||
|
|
|
|
| • Blocked air intake | • Relocate the projector to an area | ||
|
|
|
| The internal |
| with proper ventilation. | ||
|
|
|
|
|
|
|
| |
| Temperature |
| Red on/ | • Cooling fan break- | • Take the projector to your nearest | |||
| Off | temperature is | ||||||
| warning | Standby | down | |||||
|
| abnormally high. | Authorized SharpVision Service | |||||
| indicator |
|
| • Internal circuit failure | ||||
|
|
|
|
| • Clogged air intake | Center or Dealer for repair. | ||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| Green on | Red on | Time to change | • Remaining lamp life | • Carefully replace the lamp. (See | ||
|
| becomes 5% or less. | page 59.) | |||||
| Lamp | Green blinks |
| the lamp. | • Take the projector to your nearest | |||
| when the |
|
|
| Authorized SharpVision Service | |||
| indicator |
|
|
| ||||
| lamp is | Red on/ | The lamp does | • | Center or Dealer for repair. | |||
|
| |||||||
|
| warming up. | Standby | not illuminate. | • Lamp circuit failure | • Please exercise care when | ||
|
|
|
|
|
| replacing the lamp. | ||
|
|
|
|
|
|
| ||
|
|
|
|
|
| • Securely install the cover. |
| |
|
|
|
|
| • The lamp unit cover | • If the power is not turned on even | ||
| Power | Green on/ | Off | The power is | when the lamp unit cover is | |||
| indicator | Red on | not turned on. | is open. | securely installed, contact your | |||
|
| |||||||
|
|
|
|
|
| nearest Authorized SharpVision | ||
|
|
|
|
|
| Service Center or Dealer for | ||
|
|
|
|
|
| advice. | ||
|
|
|
|
|
|
|
|
|
-58