Configuration of the ISO connections
|
|
|
|
|
|
|
|
|
|
| Configuration |
|
|
|
|
|
|
|
|
|
| 1 | unconfigured |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 | unconfigured |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | Antenna power |
| 1 |
| 2 |
| 3 |
| 4 |
|
| ||
|
|
|
|
|
|
|
| ||||
|
|
|
|
| ISO A | 4 | 12 V (Ignition | ||||
|
|
|
|
|
|
|
|
| |||
| 5 |
| 6 |
| 7 |
| 8 |
| positive) | ||
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| 5 | unconfigured |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 | Permanent positive |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 7 | unconfigured |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 8 | Minus |
|
|
|
|
|
|
|
|
|
|
| Configuration |
|
|
|
|
|
|
|
|
|
| 1 | Rear right + |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 | Front right + |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | Front left + |
|
|
|
|
|
|
|
|
|
|
|
|
| 1 |
| 2 |
| 3 |
| 4 |
|
|
|
|
|
|
|
|
| ISO B | 4 | Rear left + | ||||
|
|
|
|
|
|
|
|
| |||
| 5 |
| 6 |
| 7 |
| 8 |
|
|
|
|
|
|
|
|
|
| 5 | Rear right - | ||||
|
|
|
|
|
|
|
|
|
| 6 | Front right - |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 7 | Front left - |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 8 | Rear left - |
|
|
|
|
|
|
|
|
|
|
|
|
Of course you can also only connect the car radio to two speakers. Then you only use the cable for the front speakers.
Problems because of cable interchanging
In a few vehicle models the standard configura- tion of the connections [4] and [6] in the ISO Block A (see above "Configuration of the ISO Blocks") is interchanged at the factory. If this is the case the station memory can be lost.
To correct this the connections 4 (Ignition positive) and 6 (Permanent positive) in the ISO Block A must be swapped.
Installing the radio into the ISO duct
Note
Before installation remove, without fail, the two transport securing screws on the top of the radio housing (marked with a red sticker)!
The car radio can be installed into any standard ISO mounting duct. In the event that your vehicle does not have an ISO mounting duct contact your local specialist establishment, local dealer or the technical department of the store.
•Pull the installation bracket and the bezel frame off of the car radio's housing.
•Place the installation bracket into the ISO mounting duct.
•Bend the tabs on the installation bracket with a screw driver so that the bracket is fixed firmly into the mounting duct (see diagram).
•Check to make sure that the bracket is securely fixed.
•Connect the ISO socket block of the car radio with the two ISO plugs on your vehicle.
•Connect the antenna cable from the vehicle an- tenna to the antenna socket on the car radio.
•Feed the microphone unit cable into the mounting duct and connect it to the microphone unit socket. Run the cable in such a way that the microphone unit can later be secured in the vehicle interior.
•Contingently connect the audio cinch cable of an external amplifier to the LINE OUT socket on the car radio.
•If necessary secure your device against theft with additional measures. Attach the securing screw with the anchoring plate and the securing material to the engine firewall of the vehicle.
•Carefully push the car radio into the mounting duct until it locks into place. Finally put on the bezel frame.
- 55 -
