Manuals / Brands / Computer Equipment / Switch / SMSC / Computer Equipment / Switch

SMSC USB2640, USB2640i 6.4ROM BOOT Sequence, USB2640, USB2641, USB2640, USB2641, Figure 6.5 USB2640/USB2641 I2C Connection, Figure 6.4 USB2640/USB2641 SPI ROM Connection

1 60

Download 60 pages, 1.11 Mb

Ultra Fast USB 2.0 Multi-Format Flash Media Controller/USB Hub Combo

6.4ROM BOOT Sequence

After power-on reset, the internal firmware checks for an external SPI flash device that contains a valid signature of "2DFU" (device firmware upgrade) beginning at address 0xFFFA. If a valid signature is found, then the external ROM is enabled and code execution begins at address 0x0000 in the external SPI device. Otherwise, code execution continues from the internal ROM.

If there is no SPI ROM detected, the internal firmware then checks for the presence of an I2C ROM. The firmware looks for the signature ‘ATA2’ at the offset of 0xFC-0xFF in the I2C ROM. The firmware reads in the I2C ROM to configure the hardware and software internally. Please refer to section 7.3.2 EEPROM Data Descriptor on page 28 for the details of the configuration options.

The SPI ROM required for the USB2640/USB2641 must be 1 Mbit and support either 30 MHz or 60 MHz. The frequency used is set using the SPI_SPD_SEL. For 30 MHz operation, this pin must be pulled to ground through a 100 kΩ resistor. For 60 MHz operation, this pin must pulled up through a 100 kΩ resistor. SPI_SPD_SEL: This pin is used to choose the speed of the SPI interface. During nRESET assertion, this pin will be tri-stated with the weak pull-down resistor enabled. When nRESET is negated, the value on the pin will be internally latched, and the pin will revert to SPI_DO functionality, the internal pull-down will be disabled.

The firmware can determine the speed of operation on the SPI port by checking the SPI_SPEED in the SPI_CTL register (0x2400 - RESET = 0x02). Both 1- and 2-bit SPI operation is supported. For optimum throughput, a 2-bit SPI ROM is recommended. Both mode 0 and mode 3 SPI ROMS are also supported.

USB2640/

USB2641

SPI_CE_N	CE#
SPI_CLK / GPIO4 / SCL	CLK
	CLK

SPI ROM

	SPI_DO / GPIO5 / SDA / SPI_SPD_SEL		DO
	SPI_DI		DO
	SPI_DI		DI

Figure 6.4 USB2640/USB2641 SPI ROM Connection

USB2640/

USB2641

3.3V

10K

SCL

3.3V

I2C ROM

10K

SDA

Figure 6.5 USB2640/USB2641 I2C Connection

Revision 2.0 (10-03-08)	26	SMSC USB2640/USB2641
	DATASHEET

Contents

USB2640/USB2641 Ultra Fast USB 2.0 Multi-Format Flash Media Controller/USB Hub Combo Datasheet Page Table of Contents Page List of Tables List of Figures Chapter 1 Overview 1.1Device Features 1.2OEM Selectable Features Chapter 2 Acronyms Chapter 3 Pin Configurations Figure 3.2 USB2641 48-PinQFN Chapter 4 Pin Tables 4.148-PinTables Table 4.2 USB2641 48-PinTable SECURE DIGITAL / MEMORY STICKINTERFACE (14 PINS) DIGITAL POWER, NO CONNECTS (9 PINS) Diagrams Block 5 Chapter Page Chapter 6 Pin Descriptions 6.1USB2640/USB2641 Pin Descriptions Table 6.1 USB2640/USB2641 Pin Descriptions (continued) MEMORY STICK INTERFACE SECURE DIGITAL / MULTIMEDIACARD INTERFACE USB INTERFACE Note: SPI INTERFACE Page MISC DIGITAL / POWER / GROUND 6.2Buffer Type Descriptions 6.3Port Power Control USB2640 USB2641 6.4ROM BOOT Sequence Chapter 7 Configuration Options 7.1Hub 7.1.1.1Power Switching Polarity 7.2Card Reader 7.3System Configurations 7.3.2EEPROM Data Descriptor Table Internal Flash Media Controller Configurations REG ADDR REGISTER NAME Table 7.1 Internal Flash Media Controller Configurations (continued) Table 7.2 Hub Controller Configurations 7.3.2.10h-19h:USB Serial Number Option 7.3.2.21Ah-1Bh:USB Vendor ID Option 7.3.2.31Ch-1Dh:USB Product ID Option 7.3.2.41Eh-21h:USB Language Identifier Option 7.3.2.522h-5Dh:USB Manufacturer String Length 7.3.2.65Eh-99h:USB Product String Length 7.3.2.79Ah: USB BmAttribute (1 byte) 7.3.2.89Bh: USB MaxPower (1 byte) 7.3.2.99Ch-9Fh:Attribute Byte Descriptions 7.3.2.10A4h-A5h:LUN Power Configuration 7.3.2.11A8h: LED Blink Interval (1 byte) 7.3.2.12A9h: Blink Duration (1 byte) 7.3.3.1AAh-B0h:Lun 0 Identifier String 7.3.3.2B1h-B7h:Lun 1 Identifier String 7.3.3.3B8h-BEh:Lun 2 Identifier String 7.3.3.4BFh-C5h:Lun 3 Identifier String 7.3.3.5C6h-CDh:Inquiry Vendor String 7.3.3.6CEh-D2h:Inquiry Product String 7.3.3.7D3h: Dynamic Number of Luns 7.3.3.8D4h-D7h:Lun to Device Mapping 7.3.3.9D8h-DAh:Reserved 7.3.3.10DBh-DDh:Reserved 7.3.3.11DEh: Vendor ID (LSB) 7.3.3.12DFh: Vendor ID (MSB) 7.3.3.13E0h: Product ID (LSB) 7.3.3.14E1h: Product ID (MSB) 7.3.3.15E2h: Device ID (LSB) 7.3.3.16E3h: Device ID (MSB) 7.3.3.17E4h: Config Data Byte 1 (CFG_DAT_BYT1) 7.3.3.18E5h: Config Data Byte 2 (CFG_DAT_BYT2) 7.3.3.19E6h: Config Data Byte 3 (CFG_DAT_BYT3) 7.3.3.20E7h: Non-RemovableDevice 7.3.3.21E8h: Port Disable For Self-PoweredOperation 7.3.3.22E9h: Port Disable For Bus-PoweredOperation 7.3.3.23EAh: Max Power For Self-PoweredOperation 7.3.3.24EBh: Max Power For Bus-PoweredOperation 7.3.3.25ECh: Hub Controller Max Current For Self-PoweredOperation 7.3.3.26EDh: Hub Controller Max Current For Bus-PoweredOperation 7.3.3.27EEh: Power-OnTime 7.3.3.28EFh: Boost_Up 7.3.3.29F0h: Boost_3:0 7.3.3.30F1h: Port Swap 7.3.3.31F2h: Port Remap 7.3.3.32F3h: Port Remap 7.3.3.33F4h: MS/SD Clock Limit 7.3.3.34F5h: Reserved 7.3.3.35F6h: Reserved FCh-FFh: 7.3.4.1Implementation Characteristics 7.4Default Configuration Option: 7.5Reset 7.5.2.1RESET_N for EEPROM Configuration Chapter 8 Pin Reset States 8.1Pin Reset States Table 8.2 USB2640 Pin Reset States (continued) Table 8.3 USB2641 Pin Reset States Table 8.3 USB2641 Pin Reset States (continued) Chapter 9 DC Parameters 9.1Maximum Guaranteed Ratings 9.2Operating Conditions 9.3DC Electrical Characteristics Input Leakage O12 Type Buffer I/O12, I/O12PU & I/O12PD Type Buffer IO-U 9.4Capacitance Chapter 10 AC Specifications 10.1Oscillator/Clock (C1 + CS1) x (C2 + CS2) CL (C1 + CS1 + C2 + CS2) Chapter 11 Package Outline Chapter 12 GPIO Usage