Manuals / Brands / Computer Equipment / Switch / SMSC / Computer Equipment / Switch

SMSC USB2640, USB2640i Chapter 9 DC Parameters, 9.1Maximum Guaranteed Ratings, MIN, MAX, Note, Note, UNITS, SYMBOL, COMMENTS, PARAMETER, Figure 9.1 Supply Rise Time Models

1 60

Download 60 pages, 1.11 Mb

Ultra Fast USB 2.0 Multi-Format Flash Media Controller/USB Hub Combo

Chapter 9 DC Parameters

9.1Maximum Guaranteed Ratings

PARAMETER	SYMBOL	MIN	MAX	UNITS	COMMENTS

Storage	TSTOR	-55	150	°C
Temperature

Lead			325	°C	Soldering < 10 seconds
Temperature

3.3V supply	VDD33,	-0.5	4.0	V
voltage	VDDA33
Voltage on		-0.5	(3.3V supply voltage + 2) ≤ 6	V
USB+ and
USB- pins

Voltage on		-0.5	VDD33 + 0.3	V	When internal power FET
GPIO10					operation of these pins are
					enabled, these pins may be
					simultaneously shorted to
					ground or any voltage up to
					3.63V indefinitely, without
					damage to the device as
					long as VDD33 and VDDA33
					are less than 3.63V and TA
					is less than 70oC.
Voltage on		-0.5	VDD33 + 0.3	V
any signal pin

Voltage on		-0.5	3.6	V
XTAL1

Voltage on		-0.5	2.0	V
XTAL2

Note 9.1 Stresses above the specified parameters may cause permanent damage to the device. This is a stress rating only. Functional operation of the device at any condition above those indicated in the operation sections of this specification is not implied.

Note 9.2 When powering this device from laboratory or system power supplies the Absolute Maximum Ratings must not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on their outputs when the AC power is switched on or off. In addition, voltage transients on the AC power line may appear on the DC output. When this possibility exists, a clamp circuit should be used.

Voltage		tRT		Voltage		tRT
		tRT				tRT
VDD33			3.3V	100% VDD18			1.8V	100%
		90%				90%
VSS	10%			VSS	10%
VSS				VSS
	t10%	t90%	Time		t10%	t90%	Time

Figure 9.1 Supply Rise Time Models

Revision 2.0 (10-03-08)	54	SMSC USB2640/USB2641
	DATASHEET

Contents

USB2640/USB2641 Ultra Fast USB 2.0 Multi-Format Flash Media Controller/USB Hub Combo Datasheet Page Table of Contents Page List of Tables List of Figures Chapter 1 Overview 1.1Device Features 1.2OEM Selectable Features Chapter 2 Acronyms Chapter 3 Pin Configurations Figure 3.2 USB2641 48-PinQFN Chapter 4 Pin Tables 4.148-PinTables Table 4.2 USB2641 48-PinTable SECURE DIGITAL / MEMORY STICKINTERFACE (14 PINS) DIGITAL POWER, NO CONNECTS (9 PINS) Diagrams Block 5 Chapter Page Chapter 6 Pin Descriptions 6.1USB2640/USB2641 Pin Descriptions Table 6.1 USB2640/USB2641 Pin Descriptions (continued) MEMORY STICK INTERFACE SECURE DIGITAL / MULTIMEDIACARD INTERFACE USB INTERFACE Note: SPI INTERFACE Page MISC DIGITAL / POWER / GROUND 6.2Buffer Type Descriptions 6.3Port Power Control USB2640 USB2641 6.4ROM BOOT Sequence Chapter 7 Configuration Options 7.1Hub 7.1.1.1Power Switching Polarity 7.2Card Reader 7.3System Configurations 7.3.2EEPROM Data Descriptor Table Internal Flash Media Controller Configurations REG ADDR REGISTER NAME Table 7.1 Internal Flash Media Controller Configurations (continued) Table 7.2 Hub Controller Configurations 7.3.2.10h-19h:USB Serial Number Option 7.3.2.21Ah-1Bh:USB Vendor ID Option 7.3.2.31Ch-1Dh:USB Product ID Option 7.3.2.41Eh-21h:USB Language Identifier Option 7.3.2.522h-5Dh:USB Manufacturer String Length 7.3.2.65Eh-99h:USB Product String Length 7.3.2.79Ah: USB BmAttribute (1 byte) 7.3.2.89Bh: USB MaxPower (1 byte) 7.3.2.99Ch-9Fh:Attribute Byte Descriptions 7.3.2.10A4h-A5h:LUN Power Configuration 7.3.2.11A8h: LED Blink Interval (1 byte) 7.3.2.12A9h: Blink Duration (1 byte) 7.3.3.1AAh-B0h:Lun 0 Identifier String 7.3.3.2B1h-B7h:Lun 1 Identifier String 7.3.3.3B8h-BEh:Lun 2 Identifier String 7.3.3.4BFh-C5h:Lun 3 Identifier String 7.3.3.5C6h-CDh:Inquiry Vendor String 7.3.3.6CEh-D2h:Inquiry Product String 7.3.3.7D3h: Dynamic Number of Luns 7.3.3.8D4h-D7h:Lun to Device Mapping 7.3.3.9D8h-DAh:Reserved 7.3.3.10DBh-DDh:Reserved 7.3.3.11DEh: Vendor ID (LSB) 7.3.3.12DFh: Vendor ID (MSB) 7.3.3.13E0h: Product ID (LSB) 7.3.3.14E1h: Product ID (MSB) 7.3.3.15E2h: Device ID (LSB) 7.3.3.16E3h: Device ID (MSB) 7.3.3.17E4h: Config Data Byte 1 (CFG_DAT_BYT1) 7.3.3.18E5h: Config Data Byte 2 (CFG_DAT_BYT2) 7.3.3.19E6h: Config Data Byte 3 (CFG_DAT_BYT3) 7.3.3.20E7h: Non-RemovableDevice 7.3.3.21E8h: Port Disable For Self-PoweredOperation 7.3.3.22E9h: Port Disable For Bus-PoweredOperation 7.3.3.23EAh: Max Power For Self-PoweredOperation 7.3.3.24EBh: Max Power For Bus-PoweredOperation 7.3.3.25ECh: Hub Controller Max Current For Self-PoweredOperation 7.3.3.26EDh: Hub Controller Max Current For Bus-PoweredOperation 7.3.3.27EEh: Power-OnTime 7.3.3.28EFh: Boost_Up 7.3.3.29F0h: Boost_3:0 7.3.3.30F1h: Port Swap 7.3.3.31F2h: Port Remap 7.3.3.32F3h: Port Remap 7.3.3.33F4h: MS/SD Clock Limit 7.3.3.34F5h: Reserved 7.3.3.35F6h: Reserved FCh-FFh: 7.3.4.1Implementation Characteristics 7.4Default Configuration Option: 7.5Reset 7.5.2.1RESET_N for EEPROM Configuration Chapter 8 Pin Reset States 8.1Pin Reset States Table 8.2 USB2640 Pin Reset States (continued) Table 8.3 USB2641 Pin Reset States Table 8.3 USB2641 Pin Reset States (continued) Chapter 9 DC Parameters 9.1Maximum Guaranteed Ratings 9.2Operating Conditions 9.3DC Electrical Characteristics Input Leakage O12 Type Buffer I/O12, I/O12PU & I/O12PD Type Buffer IO-U 9.4Capacitance Chapter 10 AC Specifications 10.1Oscillator/Clock (C1 + CS1) x (C2 + CS2) CL (C1 + CS1 + C2 + CS2) Chapter 11 Package Outline Chapter 12 GPIO Usage