Sony HBD-E370/E470/ E570/E870/T57 Screen 12 *FA Mode Test Not Used, Networking Confirmation

HBD-E370/E470/E570/E870/T57

Screen 12: *FA Mode Test (Not Used)

(Screen 12)

FA Mode Test

[1]Enter Repeat FA mode Repeat number: 0000

[2]Save FE log to USB

Not used for the servicing.

Press the [RETURN] button if having entered this mode.

CONFIRMATION ITEM

1.Playback Operation Confirmation 1-1. Test Disc

Part No.	Description	Layer
J-6090-199-A	BLX-104	Single Layer
J-6090-200-A	BLX-204	Dual Layer
J-2501-307-A	CD (HLX-A1)
J-2501-305-A	HLX-513	Single Layer (NTSC)
J-2501-306-A	HLX-514	Dual Layer (NTSC)
J-6090-077-A	HLX-506	Single Layer (PAL)
J-6090-078-A	HLX-507	Dual Layer (PAL)

Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883- 989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.

Operation and Display:

1.BLX-104 Procedure:

1.Select 23.976Hz/1080p.

2.Play “4.Motion picture”.

3.Check whether player can play back or not.

4.Check each outputs. Video:

Composite/S Video/component/HDMI.

Audio:

Speaker out.

*When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) can use instead of 1080/24p.

However this is temporary correspondence.

*When the output of HDMI is 1080p, the signal of Composite/S Video/Component are not output.

It is necessary to lower the output of HDMI to 1080i or less.

2.BLX-204 Procedure:

1.Select 1080i (59.94Hz or 50Hz).

2.Play “4.Motion picture”.

3.Check whether player can play back or not. (Check the picture and sound output)

3.CD (HLX-A1) Procedure:

Check whether player can play back or not. (Check the sound output)

4.HLX-513/514 (NTSC), HLX-506/507 (PAL) Procedure:

1.After displayed Main Menu, select “1.Video Signal”.

2.Play “1.Color bar 100%”.

(Check the picture and sound output)

3.Return to Menu.

4.Play “Demonstration 4:3” or “Demonstration 16:9”. (Check the picture and sound output)

1-2. Playback operation confirmation

Confirm operation in each signal/output mode of test disc (BLX- 104/204) according to the content of the repair.

Note: “AV Sync.” doesn’t operate.

2. Networking Confirmation

Confirm it according to the following procedure when you confirm the connection of the network.

Note: Do not execute “Network Connection Diagnostics” of “Network Settings” of the home menu with only the router connected.

Procedure:

1.Connect the router with the set with LAN cable.

2.Turn on the power of the set and the router.

3.Press the [HOME] button on the remote commander, and the home menu is displayed.

4.Select “Setup” → “Network Settings” → “Internet Settings”, and press the [3] button on the remote commander.

5.Select “View Networks Status” and press the [3] button on the remote commander.

6.Confirm IP address are displayed in “IP Address”, “Subnet Mask” and “Default Gateway”.

Physical Connection:	XXXX
Internet Access:	XXXX
IP Address Setting:	XXXX
IP Address:	XXX.XXX.XXX.XXX
Subnet Mask:	XXX.XXX.XXX.XXX
Default Gateway:	XXX.XXX.XXX.XXX
DNS Settings:	XXXX
Primary DNS:	XXX.XXX.XXX.XXX
Secondary DNS:	XXX.XXX.XXX.XXX
MAC Address:	XXX.XXX.XXX.XXX

26