– 20 –

MDP manufacturer code numbers

Manufacturer

Code number

Sony

701

Kenwood

707

Magnavox

703

Maranz

702

Mitsubishi

702

Panasonic

704

Philips

703

Pioneer

702

RCA

702

Sanyo

706

Sharp

705

Yamaha

703

Notes

If more than one code number is listed, try entering them one by one, until you come to the correct code for your equipment.

In some rare cases, you may not be able to operate your non- Sony video equipment with the supplied remote control. This is because your equipment may use a code that is not included with this remote control. In this case, please use the equipment’s own remote control unit.

The code numbers for Sony equipment are assigned at the factory as follows:

VHS VCR

301

(preset code for the supplied

 

 

remote control)

8 mm VCR

302

 

Beta, ED Beta VCRs

303

 

Whenever you remove the batteries — to replace them, for example — if too much time is taken, the code number may revert to the factory setting and must be reset.

36-ENOperations

Operating video equipment

 

 

 

VTR (POWER)

VTR (FUNCTION)

 

 

 

Video operating

 

 

 

buttons

 

 

 

1

2

3

 

4

5

6

0 – 9 buttons

7

8

9

 

 

0

 

ENTER

CH +/–

Use the video operating buttons on the remote control to operate the video equipment.

Press VTR (FUNCTION) before operating the video equipment.

Operating a VCR

Buttons on the remote control

To turn on or off

Press VTR (POWER).

To select a channel

Press the 0 – 9 buttons.

directly

 

To change channels

Press CH +/–.

To record

Press ( while pressing r. First release

 

(, then release r.

To play

Press (.

To stop

Press p.

To fast forward

Press ).

To rewind the tape

Press 0.

To pause

Press P.

 

To resume normal playback, press again.

To search the picture

Press ) or 0 during playback.

forward or backward

To resume normal playback, release the

 

button.

To change input mode

Press TV/VTR.

Operating an MDP

Buttons on the remote control

To turn on or off

Press VTR (POWER).

To play

Press (.

To stop

Press p.

To pause

Press P.

 

To resume normal playback, press again.

To search the picture

Keep pressing ) or 0 during

forward or backward

playback.

 

To resume normal playback, release the

 

button.

To search the chapter

Press CH +/–.

forward and backward

 

N o t e

 

If the video equipment does not have a certain function, the corresponding button on this remote control will not operate.

Operating a cable box or DBS receiver

You can program the supplied remote control to operate a cable box or DBS receiver. Follow the procedures below to set the manufacturer’s code number in the remote control.

 

 

 

DBS/CABLE (POWER)

 

 

 

DBS/CABLE

 

 

 

 

(FUNCTION)

 

DISPLAY*

 

 

 

 

1

2

3

 

 

4

5

6

0 – 9 buttons

 

7

8

9

 

 

JUMP

0

 

ENTER

 

TV/DBS*

 

 

GUIDE*

 

 

 

 

V/v/B/b/

*

MENU*

CH +/–

CODE SET

*The TV/DBS, GUIDE, DISPLAY, V/v/B/b/ , and MENU buttons can be used only with a DBS receiver.

1 Turn off the equipment you want to set up, and press DBS/CABLE (FUNCTION).

FUNCTION

DBS/CABLE

2 Press the CODE SET, DBS/CABLE (FUNCTION), and 0 – 9 buttons to enter the manufacturer’s code number (see the chart on the right column), then press ENTER. For example, to program your remote control to operate a Sony DBS receiver, press CODE SET, DBS/CABLE (FUNCTION), 8, 0, 1, and

ENTER.

FUNCTION

 

ENTER

CODE SET DBS/CABLE

 

0

1

8

3 Press DBS/CABLE (POWER) to turn on the cable box or DBS receiver.

DBS/CABLE

4 Use the cable box/DBS control buttons to check if the code number works.

For example, to operate a cable box or DBS receiver, you can use the DBS/CABLE (POWER), JUMP, CH +/–, 0 – 9 and ENTER buttons.

N o t e

If the cable box or DBS receiver does not have a certain function, the corresponding button on this remote control will not operate.

To operate the projection TV

Press TV (FUNCTION). Then use the projection TV control buttons to control the projection TV.

For more details on operating the cable box or DBS receiver

Refer to the operating instructions that come with the

equipment.EN

If the remote control doesn’t work

First, try repeating the setup procedures using the other codes listed for your equipment.

Manufacturer code numbers (cable box)

Manufacturer

Code number

Hamlin/Regal

222, 223, 224, 225, 226

Jerrold/G. I.

201, 202, 203, 204, 205, 206, 207, 208,

 

218

Oak

227, 228, 229

Panasonic

219, 220, 221

Pioneer

214, 215

Scientific Atlanta

209, 210, 211

Tocom

216, 217

Zenith

212, 213

Manufacturer code numbers (DBS receiver)

Manufacturer

Code number

Sony

801

(preset code for the supplied

 

 

remote control)

RCA

802

 

Notes

If more than one code number is listed, try entering them one by one until you come to the correct code for your equipment.

If you enter a new code number, the code number you previously entered at that setting is erased.

In some rare cases, your equipment may use a code that is not provided with this remote control and you may not be able to operate your equipment with the supplied remote control. In this case, use the equipment’s own remote control unit.

Whenever you remove the batteries — to replace them, for example — if too much time is taken, the code numbers may revert to the factory setting and must be reset.

Operations 37-EN

Page 20
Image 20
Sony KP-41T65C service manual Operating a cable box or DBS receiver, Operating video equipment