(5) Feature ID Map |
|
| DESTINATION |
|
|
|
|
|
|
|
|
|
| KV- |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| 1 | 2 7 S 4 0 | (US) | 153 | 1 | 13 | 195 | 31 | 1 | 0 | 64 |
| 2 | 2 7 S 4 0 | (CND) | 129 | 1 | 13 | 195 | 31 | 1 | 0 | 64 |
| 3 | 2 7 S 4 5 | (US) | 153 | 27 | 13 | 195 | 31 | 1 | 1 | 64 |
| 4 | 2 7 S 4 5 | (CND) | 129 | 27 | 13 | 195 | 31 | 1 | 1 | 64 |
| 5 | 2 7 S 6 5 | (US) | 153 | 27 | 15 | 195 | 31 | 1 | 7 | 64 |
| 6 | 2 7 S 6 5 | (CND) | 129 | 27 | 15 | 195 | 31 | 1 | 7 | 64 |
| 7 | 2 9 S L 4 0 | (E) | 145 | 1 | 141 | 195 | 63 | 1 | 0 | 64 |
| 8 | 2 9 S L 4 0 A | (E) | 151 | 1 | 141 | 195 | 55 | 1 | 0 | 64 |
| 9 | 2 9 S L 4 0 C | (E) | 145 | 1 | 141 | 195 | 63 | 1 | 0 | 64 |
| 10 | 2 9 S L 4 5 | (E) | 145 | 27 | 141 | 195 | 63 | 1 | 1 | 64 |
| 11 | 2 9 S L 6 5 | (E) | 145 | 27 | 143 | 195 | 63 | 1 | 7 | 64 |
| 12 | 2 9 S L 6 5 C | (E) | 145 | 19 | 143 | 195 | 63 | 1 | 7 | 64 |
| 13 | 2 9 X L 4 0 M | (MX) | 145 | 1 | 141 | 195 | 63 | 1 | 0 | 64 |
| 14 | 2 9 X L 4 0 P | (E) | 145 | 1 | 141 | 195 | 63 | 1 | 0 | 64 |
| 15 | 2 9 X T 1 1 A | (E) | 151 | 1 | 141 | 195 | 55 | 1 | 0 | 64 |
5-2. A BOARD ADJUSTMENTS
H. FREQUENCY ADJUSTMENT
1.Input a monoscope signal.
2.Set to Service adjustment Mode.
3.Connect a frequency counter to base of Q501
4.Select the item of AFC, set to 3 level (free run).
5.Check H. Frequency for the 15735 ± 200 Hz. (NTSC) or check H. Frequency for the 15650 ± 200 Hz. (Trinorma)
6.Select the item of AFC again, adjust the level "0".
7.Write into the memory by pressing
then 
.
V. FREQUENCY ADJUSTMENT
1.Select video 1 with no signal input.
2.Set the conditions with standard setting.
3.Connect the frequency counter across
4.Check V. Frequency for the 60 ± 2 Hz (NTSC)
5.Check V. Frequency for the 50 ± 2 Hz (Trinorma).
SUB CONTRACT ADJUSTMENT (SCON)
1.Input a
2.Select the red color.
3.Set to Service adjustment Mode.
4.Select the item DCOL to "0" level.
5.Set the conditions as follows.
PICTURE | MAX |
COLOR | MIN |
BRIGHT | CENTER |
R ON | ON (1) |
G ON | OFF (0) |
B ON | OFF (0) |
1: ON
0: OFF
SERVICE RON 1
6.Connect an oscilloscope probe to C Board, CN301 Pin 5 (RED OUT).
7.Select RDRV with 
and 
.
8.Adjust with 
and 
for: 1.90 ± 0.05
Whiten
1.90 ± 0.05
n
Black
9.Reset the item DCOL to "1" level.
10.Write the memory by pressing 
then 
.
11.Return the following back to normal after adjustment.
PICTURE | MAX |
COLOR | CENTER |
BRIGHT | CENTER |
R ON | ON (1) |
G ON | ON (1) |
B ON | ON (1) |
— 32 —
