To know the recording

• Even when there is no recorded sound on the

condition

 

 

sound source, there may be cases when

The REC LED lights up or flashes

recording does not pause automatically during

synchro-recording due to the noise level

according to the recording condition.emitted from the sound source.

 

 

 

 

• If a silent portion is encountered for

Recording

 

REC indicator

 

 

 

approximately 2 seconds during synchro-

condition

 

 

 

 

 

 

recording from a sound source other than a

 

 

 

 

While recording

 

lights up

 

CD or an MD, a new track mark is

 

 

flashes according

 

automatically added at the point where the

 

 

to the loudness

of

silent portion ends.

 

 

the source while

 

• Synchro-recording cannot be done if the

 

 

recording with a

 

connecting cord is not an optical cable, or if

 

 

microphone

 

the cable is connected to the MIC (PLUG IN

 

 

(voice mirror)

 

POWER) jack.

 

 

 

 

• You cannot change the recording mode during

Recording standby

 

flashes

 

 

 

recording.

 

 

 

 

• “Data Save” or “TOC Edit” flashes while data

Less than 3 minutes’

flashes slowly

 

 

of the recording (the track’s start and end

recording time

 

 

 

 

 

 

points, etc.) is being recorded. Do not move or

available

 

 

 

 

 

 

jog the recorder or disconnect the power

 

 

 

 

A track mark has

 

goes off

 

source while the indication is flashing in the

been added (when

 

momentarily

 

display.

controlling by the

 

 

 

• The lid does not open until“TOC Edit”

recorder only)

 

 

 

disappears in the display.

 

 

 

 

• If the power supply is disrupted (i.e. the

While checking-out

 

flashes faster

 

 

 

battery is removed or becomes exhausted or

About the DSP TYPE-R for ATRAC

the AC power adaptor is disconnected) during

a recording or editing operation, or while

“TYPE-R” is a high-level Sony specification

“TOC Edit” appears in the display, then it will

used in the Digital Signal Processor (DSP),

not be possible to open the lid until power is

which is heart of the MiniDisc sound. This

restored.

technology gives the MiniDisc recorder twice

• You can make digital recording only from an

the signal processing capability as previous

optical type output.

MiniDisc Walkman models, producing a sound

• When recording from a portable CD player,

quality close to that of MiniDisc decks. This

set the CD player to pause, and then do the

unit supports the “TYPE-R” function only

recording procedure on the recorder.

during recording or playback in normal stereo

• Note the following when recording from a

mode. It does not support this function in

portable CD player:

MDLP mode, or during the checking out of

—Some portable CD players may not be

audio data from the computer in normal stereo

capable of digital out when the AC power

mode using OpenMG Jukebox.

adaptor is disconnected. If this is the case,

Notes

connect the AC power adaptor to the

portable CD player and use it on AC power

• The pause function cannot be turned on or off

as the power source.

manually during synchro-recording. Flip the

—On some portable CD players, optical

 

control bar towardsx to stop recording.

• Do not switch the“SYNC REC” setting while

output may not be possible when using an

anti-skip function (e.g., ESP* or G-

recording. Recording may not be done

PROTECTION). If this is the case, turn off

properly.

the anti-skip function.

 

 

∗ Ελεχτρονιχ Σηοχκ Προτεχτιον

22