MZ-R900
Pin No. | Pin Name | I/O |
| Description |
|
| |
|
|
|
| ||||
204 | XPD ADA | O | Power supply control signal output for the drive to A/D, D/A converter (IC301) | ||||
|
|
|
|
| |||
205 | XCS LCD | O | Chip select signal output to the liquid crystal display element |
| |||
|
|
|
|
|
| ||
206 | LCD STB | O | Strobe signal output to the liquid crystal display element |
|
| ||
207 | LCD RST | O | Reset control signal output to the liquid crystal display element | Not used (open) | |||
208 | REC LED | O | LED ON/OFF control signal output for REC display |
|
| ||
|
|
|
|
| |||
209 | LD ON | O | ON/OFF control signal output terminal of the laser diode | Not used (open) | |||
|
|
|
|
|
|
| |
210 | TSB SLV CHK | I | TSB slave detection signal input terminal |
|
|
| |
|
|
|
|
|
|
|
|
211, 212 | NC | I | Not used (open) |
|
|
|
|
|
|
|
|
|
| ||
213 | MCUVSS1 | — | Ground terminal (for the microcomputer block) |
|
| ||
214 | CAV CLV SW | O | CAV/CLV changeover control signal output | Not used (open) |
| ||
215 | XOPT CTL | O | Power supply ON/OFF control signal output for DIN PD drive |
| |||
|
|
|
|
|
|
| |
216 | CS RTC | O | Chip select signal output to the clock IC |
|
|
| |
|
|
|
|
|
|
| |
217 | OFTRK | I | Off track signal input from RF amp (IC501) |
|
|
| |
|
|
|
|
|
| ||
218 | NC | O | Analog muting control signal output | “H”: muting ON | Not used (open) | ||
219 | XCS NV | O | Chip select signal output to EEPROM (IC804) |
|
|
| |
220 | XRST MTR | O | Reset control signal output to the motor driver (IC551) |
|
| ||
DRV |
|
| |||||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
221 | XRF RST | O | Reset control signal output to RF amp (IC501) |
|
|
| |
|
|
|
|
| |||
222 | MCUVDD3 | — | Power supply terminal (for the microcomputer block) (+1.5V) |
| |||
|
|
|
|
| |||
223 | SPDL MON | I | Spindle servo monitor signal input from the motor driver (IC551) |
| |||
|
|
|
|
|
|
|
|
224 to | NC | I | Not used (open) |
|
|
|
|
226 |
|
|
|
| |||
|
|
|
|
|
|
| |
|
|
|
|
| |||
227 | XHOLD SW | I | HOLD switch (S801) input terminal | “L”: hold ON, “H”: hold OFF | |||
228 | SYNC REC | I | SYNCHRO REC switch (S802) input terminal | “L”: OFF, “H”: ON | |||
229 | NC | O | Not used (open) |
|
|
|
|
|
|
|
| ||||
230 | PROTECT | I | Detection input terminal of the record check claw from the protect detection switch (S803) | ||||
“L”: recording possible condition, “H”: protect |
|
| |||||
|
|
|
|
| |||
231 | FLASHVDD | — | Power supply terminal (for the internal FLASH ROM) (+2.4V) |
| |||
|
|
|
|
|
| ||
232 | FLASHVSS | — | Ground terminal (for the internal FLASH ROM) |
|
| ||
233 | SLD MON | I | Sled servo monitor signal input from the motor driver (IC551) |
| |||
234 | VLON | O | Power supply control signal output for the laser diode drive to the power control (IC901) | ||||
235 | SLEEP | O | System sleep control signal output to the power control (IC901) | “H”: sleep ON | |||
|
|
|
| ||||
236 | FFCLR | O | Input latch output for the start switching to the power control (IC901) | ||||
|
|
|
|
| |||
237 | CHG GAIN | O | Charge gain control signal output to the power control (IC601) |
| |||
|
|
|
| ||||
238 | CHG | O | Charge ON/OFF control signal output to the power control (IC601) “H”: charge ON | ||||
239, 240 | NC | O | Not used (open) |
|
|
|
|
241 | MIFVDD3 | — | Power supply terminal (for the microcomputer I/F block) (+2.3V) |
| |||
242 | MIFVSS2 | — | Ground terminal (for the microcomputer I/F block) |
|
| ||
|
|
|
|
|
| ||
243 | TEST2 | O | Input terminal for the main test (normally open) |
|
| ||
|
|
|
|
|
|
|
|
244 | NC | — | Not used (open) |
|
|
|
|
|
|
|
|
|
|
|
|
38
