•MAIN BOARD IC801
Pin No. |
| Pin Name | I/O | Description | ||
|
|
|
|
|
|
|
1 |
| SYNC REC | I | SYNCHRO REC switch (S801) input terminal | “L”: off, “H”: on | |
|
|
|
|
|
| |
2 |
| OFTRK | I | Off track signal input from the CXD2660GA (IC502) | ||
|
|
|
|
|
| |
3 |
| PROTECT | I | |||
| “L”: recording possible , “H”: protect |
| ||||
|
|
|
|
|
| |
|
|
|
|
|
|
|
4 |
| PAUSE KEY | I | Set pause key input terminal |
| |
|
|
|
|
|
| |
5 |
|
| TX | O | Recording data output enable signal output to the CXD2660GA (IC502) | |
|
| Writing data transmission timing output |
| |||
|
|
|
|
|
| |
|
|
|
|
|
| |
6 |
| SENSE | I | Internal status (SENSE) input from the CXD2660GA (IC502) | ||
|
|
|
|
|
| |
7 |
| WRPWR | O | Laser power select signal output to the CXD2660GA (IC502) | ||
| “L”: playback mode , “H”: recording mode |
| ||||
|
|
|
|
|
| |
|
|
|
|
|
| |
8 |
| XLAT | O | Serial data latch pulse output to the CXD2660GA (IC502) | ||
|
|
|
|
|
| |
9 |
| XCS DSP | O | Chip select signal output to the CXD2660GA (IC502) | ||
|
|
|
|
|
| |
10 |
| CS RTC | O | Chip select signal output to the real time clock (IC804) | ||
|
|
|
|
|
| |
11 |
|
| SI0 | I | Serial data input from the A/D, D/A converter (IC301), CXD2660GA (IC502), EEPROM | |
|
| (IC802), real time clock (IC804) and switch & liquid crystal display module unit | ||||
|
|
|
|
| ||
|
|
|
|
|
| |
12 |
| SO0 | O | Serial data output to the A/D, D/A converter (IC301), CXD2660GA (IC502), EEPROM (IC802), | ||
| real time clock (IC804) and switch & liquid crystal display module unit | |||||
|
|
|
|
| ||
|
|
|
|
|
| |
13 |
| SCK0 | O | Serial clock signal output to the A/D, D/A converter (IC301), CXD2660GA (IC502), EEPROM | ||
| (IC802), real time clock (IC804) and switch & liquid crystal display module unit | |||||
|
|
|
|
| ||
|
|
|
|
|
| |
14 |
| XGUM ON | I | Rechargeable battery pack detection switch (S901) input terminal | ||
| “L”: rechargeable battery pack in |
| ||||
|
|
|
|
|
| |
|
|
|
|
|
|
|
15 |
| VSS | — | Ground terminal |
| |
|
|
|
|
|
|
|
16 |
| VDD | — | Power supply terminal (+2.4V) |
| |
|
|
|
|
|
|
|
17 |
| XOUT | O | Not used (open) |
| |
|
|
|
|
|
|
|
18 |
| BEEP | O | Beep sound control signal input terminal |
| |
|
|
|
|
|
| |
19 |
| RMC DTCK | I/O | TSB serial communication data input/output terminal for remote commander with headphone | ||
|
|
|
|
|
| |
20 |
| XCS LCD | O | Chip select signal output to the liquid crystal display | ||
|
|
|
|
|
|
|
21 |
| LCD STB | O | Strobe signal output to the liquid crystal display |
| |
|
|
|
|
|
| |
22 |
| LCD RST | O | Reset control signal output to the liquid crystal display | ||
|
|
|
|
|
| |
23 |
| XHP STBY | O | Standby on/off control signal output to the line/headphone amplifier (IC303) | ||
| “L”: standby mode, “H”: amplifier on |
| ||||
|
|
|
|
|
| |
|
|
|
|
| ||
24 |
| CLV U | O | Spindle servo (U) drive signal output to the MPC17A56FTAF (IC601) | ||
|
|
|
|
| ||
25 |
| CLV V | O | Spindle servo (V) drive signal output to the MPC17A56FTAF (IC601) | ||
|
|
|
|
| ||
26 |
| CLV W | O | Spindle servo (W) drive signal output to the MPC17A56FTAF (IC601) | ||
|
|
|
|
| ||
27 |
| MODE1 | O | Power supply control signal output for over write head drive to the MPC18A20MTAEL (IC603) | ||
|
|
|
|
| ||
28 |
| MODE2 | O | Power supply control signal output for over write head drive to the MPC18A20MTAEL (IC603) | ||
|
|
|
|
| ||
29 |
| MODE3 | O | Power supply control signal output terminal for over write head drive | ||
|
|
|
|
| ||
30 |
| HD CON 1 | O | Over write head control signal output to the MPC17A17DTB (IC602) | ||
|
|
|
|
| ||
31 |
| HD CON 2 | O | Over write head control signal output to the MPC17A17DTB (IC602) | ||
|
|
|
|
|
| |
32 |
| XREC MODE | O | Not used (open) |
| |
|
|
|
|
|
| |
33 |
| LD ON | O | Laser diode on/off control signal output terminal | “L”: laser off, “H”: laser on Not used (open) | |
|
|
|
|
|
| |
34 |
| TSB SLV ON | I | TSB slave detect signal input terminal |
| |
|
|
|
|
| ||
35 |
| SLD MON 1 | I | Sled servo timing signal input from the MPC17A56FTA (IC601) | ||
|
|
|
|
| ||
36 |
| PD S0 | O | PD IC mode switching signal output to the optical | ||
37 |
| REG CTL CLK | O | Synchronizing external clock signal output terminal Not used (open) | ||
|
|
|
|
| ||
38 |
| PD S1 | O | PD IC mode switching signal output to the optical | ||
|
|
|
|
|
|
|
