Sony NSX-A777 TIME’i”REctiRiiNG, Press one of the function buttons to select a source, Prepare

TIMER

SHIFT

The unit can be turned on at a specified time every day with the built-in timer.

Preparation

Make sure the clock is set correctly.

1 Press one of the function buttons to select a source.

@If TUNER/BAND is pressed, the band cannot be selected in

this step,

2 Press TIMER repeatedly until 0 appears on the display.

When using the remote control, press TIMER while pressing

SHIFT.

Time and audio source name flash alternately.

o

3 Within 6 seconds, turn MULTI JOG to designate the timer-on time, then press ENTER or Il.

Turning MULTI JOG changes both the hour and the minute.

<or * is also available instead of MULTI JOG, Holding

these buttons down will vary the time rapidly.

4 Within 4 seconds, turn MULTI JOG to select the duration for the timer-activated period.

The duration can be set between 5 and 240 minutes in 5- minute steps.

-or ~ is also available instead of MULTI JOG,

The duration will be automatically set after 4 seconds, It will also be set if ENTER or I I is pressed within 4 seconds after step 4.

5 Adjust the volume. K

The source sound will play at the volume level set in this step

,$

when the power is turned on by the timer,

If the volume level is set to 21 or higher, however, it will ~,~?~ ;$SG

automatically be set to 20 when the power is turned on.							#&
6 Prepare		the source.					,,.,,,,
							,\.-,“.$
To	listen	to	a CD,	load the	disc to be played	first on tray 1.	‘$: ‘:
							‘!, !.;
To	listen	to	a tape,	insert	the tape into deck	1 or 2.	f

To listen to the radio, tune in to a station.

$

7 Press POWER to turn off the power.

When the timer-on time is reached, the unit turns on and begins play with the selected source.

m

You can change the source that was selected in step 1 by pressing one of the function buttons before pressing ENTER or II in step 3.

To check the timer setting

Press TIMER.

The selected source, the timer-on time, and the duration for the

timer-activated period will be displayed for 4 seconds.

To change any of the previous setting

Carry out from step 1.

However, if you do not change the timer-on time, in step 3 just press ENTER twice and continue from step 4.

To cancel the timer standby mode temporarily

Press TIMER repeatedly so that ~ disappears.

To restore the timer standby mode, press again to display ~.

Using the unit wlhile the timer is set ❑

You can use the unit normally after setting the timer.

Before turning off the power, carry out step 5 and 6.

m

●Timer playback and timer recording will not begin unless the power is turned off.

●Connected equipment cannot be turned on and off by the built- in timer of this unit, Use an external timer.

;.,, .,.,,,=,......... .,, . , - ..8“.88 0d.8!!J8’0..!0!’!!’10’!8!

TIME’i”REctiRiiNG

Timer recording is applicable for TUNER and VI DEO/AUX (with an external timer) sources only.

Press either TUNER/BAND or VIDEO/AUX to select a source,

then press TIMER repeatedly until @REC lights up cm th(~

display. Within 6 seconds, carry out the steps of “SETTING THE TIMER” from step 3 and insert the tape to be recorded on into deck 2 after step 6,

m

cWhen the power-economizing mode (page 7) has been turned on, the timer recording volume level will be O (minimum level).

●You cannot use the timer function to record from a CD or tape.

ENGLISH 27