Sony STR-DG1000 57

	Menu	Item	Parameter	Initial	Refer
				setting	page

	7-Speaker	SUB WOOFER [xxx]	NO, YES	YES	page 66
	Settings				- 70
	Settings	FRONT SP [xxxxx]	SMALL, LARGE	LARGE	- 70
		FRONT SP [xxxxx]	SMALL, LARGE	LARGE

		CENTER SP [xxxxx]	MIX, NO, SMALL, LARGE	LARGE

		SURROUND SP [xxxxx]	NO, SMALL, LARGE	LARGE

		SUR BACK SP [xxxxxx]	BI-AMP, ZONE 2, NO, SINGLE,	DUAL
			DUAL

		FRONT L xxfeet*	3feet to 22feet (1 foot** step)	9feet			Amplifier

		FRONT R xxfeet*	3feet to 22feet (1 foot** step)	9feet
		FRONT R xxfeet*	3feet to 22feet (1 foot** step)	9feet

		CENTER xxfeet*	3feet to 22feet (1 foot** step)	9feet

		SURROUND L xxfeet*	3feet to 22feet (1 foot** step)	9feet			Operations

		SURROUND R xxfeet*	3feet to 22feet (1 foot** step)	9feet
		SURROUND R xxfeet*	3feet to 22feet (1 foot** step)	9feet

		SUR BACK L xxfeet*	3feet to 22feet (1 foot** step)	9feet

		SUR BACK R xxfeet*	3feet to 22feet (1 foot** step)	9feet

		SUB WOOFER xxfeet*	3feet to 22feet (1 foot** step)	9feet

		DISTANCE UNIT	meter, feet	feet
		[xxxxx]

		SP POSI [xxxxxxxxx]	SIDE/LOW, SIDE/HIGH, BEHD/	SIDE/
			LOW, BEHD/HIGH	LOW

		SP CROSSOVER [xxxHz]	40Hz to 200Hz (10Hz step)	120Hz

	8-System	DIMMER [xxx% DOWN]	0%, 60%, 100%	0%	page 70
	Settings
	Settings	SP. IMPEDANCE [xxxx]	4 ohm, 8 ohm	8 ohm	page 39
		SP. IMPEDANCE [xxxx]	4 ohm, 8 ohm	8 ohm	page 39

	9-Auto	AUTO CAL START?			page 46
	Calibration				- 47
	Calibration	CAL TYPE	ENGINEER/FULL FLAT/FRONT	FULL FLAT	- 47
		[xxxxxxxxx]	REF

		EQ CURVE EFFECT [xxx]	OFF, ON	OFF

		A.CAL LOAD? [PRESET- x]	OFF, PRESET1, PRESET2, PRESET3	OFF

		A.CAL SAVE? [PRESET- x]	PRESET1, PRESET2, PRESET3	PRESET1

		A.CAL NAME?			page 90
		[xxxxxxxxx]

*After the measurements are completed using auto calibration, the measurement value is displayed as x’xx”.

**After the measurements are completed using auto calibration, you can adjust them in 1 inch increments.

57GB

Contents

Page Page About This Manual Table of Contents Getting Started Amplifier Operations Enjoying Surround Sound Tuner Operations Using the Remote Additional Information Description and location of parts Front panel Page About the indicators on the display Page Page Rear panel Page Remote commander RM-AAL003 Page Page 1: Installing speakers Enjoying a 5.1/7.1 channel system Example of a 5.1 channel speaker system configuration Example of a 7.1 channel speaker system configuration 2: Connecting speakers ZONE 2 connection 3a: Connecting the audio components How to hook up your components Audio input/output jacks to be connected Page Notes on playing a Super Audio CD on a Super Audio CD player Page Connecting components with analog audio jacks 3b: Connecting the video components Video input/output jacks to be connected Connecting components with HDMI jacks HDMI features Notes on HDMI connections Connecting a TV monitor Page Connecting a DVD player/DVD recorder Connecting a DVD player Connecting a DVD recorder Connecting a satellite tuner Page Function for conversion of video signals In the video input/output conversion table of the receiver Closed Caption display To connect a recording component In the video input/output conversion table classified by the menu settings 4: Connecting the antennas (aerials) 5:Preparing the receiver and the remote Inserting batteries into the remote About the command mode To switch the command mode of the receiver To switch the command mode of the RM-AAL003remote 6: Setting the speakers Setting the speaker impedance 3,7 Selecting the front speaker 7:Calibrating the appropriate settings automatically (AUTO Using the receiver as a pre- amplifier Performing the auto calibration To cancel auto calibration When error codes appear When you select “WRN CHECK” When you select “PHASE INFO” Auto Calibration menu parameters Page Selecting a component To activate the muting function To avoid damaging your speakers Listening to a Super Audio CD/CD Watching a DVD Enjoying video games Watching video Navigating through menus To return to the previous display To exit the menu Overview of the menus Page Page Adjusting the level (Level Settings menu) Level Settings menu parameters Adjusting the equalizer (EQ Settings menu) EQ Settings menu parameters To apply the stored equalizer To turn off the equalizer Clearing stored equalizer settings Settings for the surround Page Settings for the tuner (Tuner Settings menu) Tuner Settings menu parameters Settings for the audio (Audio Settings menu) Audio Settings menu parameters Settings for the video (Video Settings menu) Video Settings menu parameters Settings for the speakers (Speaker Settings menu) Speaker Settings menu parameters Page Page Page Settings for the system (System Settings menu) System Settings menu parameters Calibrating the appropriate settings automatically (Auto Enjoying Dolby Digital and DTS surround sound Type of A.F.D. mode Selecting a preprogrammed sound field (DCS) To turn off the surround effect for MOVIE/MUSIC Types of sound field available Using only the front speakers (2CH STEREO) Enjoying the surround effect at low volume levels (NIGHT MODE) Listening to the sound without any adjustment Adjusting the speaker levels and balance Resetting sound fields to the initial settings Listening to FM/AM radio 3,5 Tuner Tuning to preset stations Naming preset stations Listening to the XM Radio Activate XM Service: Connecting the XM Radio Checking the XM Radio ID Receiving XM Radio broadcasts (DIRECT TUNING) Presetting XM Radio stations Presetting channels using the preset numbers 3,5 Selecting the channel by using the preset numbers XM Radio messages list Displaying menus of the receiver on the TV screen Naming inputs Switching between digital and analog audio Listening to digital sound from other inputs Watching HDMI images from other inputs Watching component images from other inputs Assignable inputs for component video input Changing the display FM and AM band Using the Sleep Timer Recording using the receiver Recording onto a MiniDisc or audio tape To record digital sound Recording onto recording media Listening to the sound in another zone Page Page To operate the receiver using an IR repeater Using a bi-amplifierconnection To connect speakers To set up speakers Page Operating each component using the remote Table of buttons used to control each component Programming the remote The numeric codes corresponding to the component and the maker of the component To control a CD player To control a DAT deck To control an MD deck To control a tape deck To control a VCR To control a DVD player To control a DVD recorder To control a TV Performing several commands in sequence automatically Program the sequence of the operation 1,5 1,3 Setting remote control codes that are not stored in the commander To cancel learning Using a command that has been learned To erase the learned code Clearing all the contents of the remote’s memory Glossary Page Precautions On safety On power sources On heat buildup On placement Troubleshooting Audio Page Video Tuner Remote control Error message Reference sections for clearing the memory Specifications AUDIO POWER SPECIFICATIONS Page Page Index Symbols Numerics