Sony VPL-HW10 47

Setup Menu

The Setup menu is used to change the factory preset settings, etc.

Menus the Using

Status

Sets whether or not the on-screen display is displayed.

Set to “Off” to turn off the on-screen displays except for certain

menus, message when turning off the power, and warning messages.

Language

Selects the language used in the menu and on-screen displays.

Available languages are: English, Dutch, French, Italian, German,

Spanish, Portuguese, Russian, Swedish, Norwegian, Japanese,

Chinese (Simplified Chinese), Chinese (Traditional Chinese),

Korean, Thai and Arabic.

Cooling Setting

Use this item when using the projector at high altitudes.

High: Use this setting when using the projector at an altitude of

1,500 m or higher.

Standard: Use this setting when using the projector at normal

altitudes.

Note

When this item is set to “High”, the fan noise becomes slightly

louder since the number of fan rotation increases.

Standby Mode

Lowers the power consumption in standby.

When set to “Standard”, the power consumption in standby becomes

normal.

When set to “Low”, the power consumption in standby is lowered.

Note

When this item is set to “Low”, the Control for HDMI function will

not operate.

Power Saving

Sets the power saving mode.

When set to “On”, the projector goes into power saving mode if no

signal is input for 10 minutes. At that time, the ON/STANDBY

indicator lights in orange, then the screen becomes dark. In power

saving mode, the power saving mode is cancelled if a signal is input

or any button on the projector or the remote control is pressed. If you

do not want to set the projector to power saving mode, select “Off”.

47

Contents

Page THIS APPARATUS MUST BE EARTHED For customers in the USA Declaration of Conformity Disposal of Used Lamp For customers in the United States For customers in Europe For kundene i Norge Trademark Information Page Table of Contents Location of Controls Connections and Preparations Projecting Others On safety On preventing internal heat buildup Caution On repacking Location of Controls Page Page Connections and Preparations Before Setting Up the Projector Improper use Do not do any of the following while using the projector Blocking the ventilation holes (intake or exhaust) Tip Tilting front/rear and left/right Positioning the Projector and a screen When using the 16:9 aspect ratio screen size When using the 4:3 aspect ratio screen size 2 Position the projector so that the lens is parallel to the screen Top view Connecting to a VCR Page To connect to a VCR equipped with the S video connector or video connector Connecting to a Computer Page 2 Press the ?/1 (ON/STANDBY) switch to turn on the projector 3 Turn on the equipment connected to the projector 4 Press INPUT to project the picture on the screen 5 Move both lens shift dials to adjust the picture position To adjust the horizontal position To adjust the vertical position 6 Adjust the picture size using the zoom lever 7 Adjust the focus using the focus ring To adjust the tilt of the installation surface 1 Press MENU 2 Press M/m to select the Setup menu, and press , or 3 Press M/m to select “Language,” and press , or 4 Press M/m/</, to select a language, and press To clear the menu Projecting Turning Off the Power Press WIDE MODE Wide Zoom Normal Full Zoom Full 1 (When a computer signal is input) Full 2 (When a computer signal is input) Notes on selecting the wide screen mode Press one of the PICTURE MODE buttons (DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3) DYNAMIC STANDARD CINEMA 1 Press ADJ PIC 2 Make the setting or adjustment on an item When changing the adjustment level 1 Press RCP on the remote control 2 Press M/m to select “User 1,” “User 2” or “User 3,” then press 3 Select the target color you want to adjust 4 Adjust the color of the specified portions 5 After the adjustment is complete, press Press PIC MUTING Press APA Press FREEZE Using the Menus 2 Press M/m to select a menu item, and press , or ,or 4 Make the setting or adjustment of an item When changing the adjustment level Items that cannot be adjusted To reset the picture that has been adjusted To reset the items that have been adjusted Page Page Page Page Page Page Page Page Page Page Page Page About the Preset Memory No Others Power Picture On-screendisplay Remote control Others Warning Indicators Message Lists Warning messages Caution messages Tools you need to get started: •Projector Lamp LMP-H201(optional) •Standard Phillips screwdriver •Cloth (for scratch protection) 1 Turn off the projector and unplug the AC power cord 6Close the lamp cover, then tighten the screws 7Remove the filter holder 8Remove the air filter 10 Attach the filter holder 11 Wipe dust off the ventilation holes (intake) with a soft cloth 12 Place the project back on its Page Cleaning the lens Cleaning the cabinet Black points and bright points (red, blue, or green) on the screen System Input General Supplied accessories Optional accessories Preset Signals Page Preset memory numbers for each input signal Analog signal Digital signal Input Signals and Adjustable/Setting Items Screen menu Page Page Attaching the PSS-H10projector suspension support Top view Front view Side view