Sony VPL-HW10 Input, System, General

Specifications

System

Projection system

SXRD panel, 1 lens, projection system

LCD panel

0.61-inch (15.4 mm)

SXRD panel 6,220,800 pixels (2,073,600 pixels ⋅ 3)

Lens 1.6 times zoom lens (manual) f=18.5 mm to 29.6 mm F2.50 to F3.40

Lamp

200 W Ultra High Pressure Lamp Projection picture size

40 inches to 300 inches (1,016 mm to

7,620 mm) (measured diagonally) Color system

NTSC3.58/PAL/SECAM/

NTSC4.43/PAL-M/PAL-N/PAL60 system, switched automatically/ manually (PAL60 system not switched manually)

Acceptable video signals

15 kHz RGB/component 50/60 Hz, Progressive component 50/60 Hz, 480/60i, 576/50i, 480/60p, 576/50p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24PsF (48i), 1080/60p (HDMI input only), 1080/50p (HDMI input only), 1080/24p (HDMI input only), Composite video, Y/C video

Acceptable computer signals fH: 19 kHz to 72 kHz fV: 48 Hz to 92 Hz

Maximum resolution 1920 ⋅ 1080 (HDMI input only)

For details, see “Preset Signals”. (1 page 66)

Input

Video input

VIDEO: phono type Composite video: 1 Vp-p±2 dB sync negative (75 ohms terminated)

S VIDEO: Y/C mini DIN 4-pin type

Y(luminance): 1 Vp-p±2 dB sync negative (75 ohms terminated)

C (chrominance): burst 0.286 Vp-p ±2 dB (NTSC)

(75 ohms terminated), or burst 0.3 Vp-p±2 dB (PAL)

(75 ohms terminated)

Y PB/CB PR/CR

Component: phono type

Ywith Sync: 1 Vp-p±2dB sync negative (75 ohms terminated) PB/CB: 0.7 Vp-p±2dB (75 ohms terminated)

PR/CR: 0.7 Vp-p±2 dB (75 ohms terminated)

HDMI

Digital RGB/Y CB (PB) CR (PR)

INPUT A

HD D-sub 15-pins Analog RGB/component:

R/CR (PR): 0.7 Vp-p±2 dB (75 ohms terminated)

G: 0.7 Vp-p±2 dB (75 ohms terminated)

G with sync/Y: 1 Vp-p±2 dB sync negative (75 ohms terminated)

B/CB (PB): 0.7 Vp-p±2 dB (75 ohms terminated)

SYNC/HD: Composite sync input: TTL level, positive/ negative Horizontal sync input: TTL level,

positive/negative

VD: Vertical sync input: TTL level, positive/negative

REMOTE

RS-232C: D-sub 9-pins (female)

General

Dimensions

407.4mm ⋅ 179.2 mm ⋅

463.9mm (16 1/8 ⋅ 7 1/8 ⋅ 18 3/8 inches) (w/h/d)

Mass Approx. 10 kg (22 lb 1 oz) Power requirements

AC 100 V to 240 V, 3.0 A to 1.3 A, 50/60 Hz

Power consumption Max. 300 W Standby mode: 8 W Standby mode (low): 0.5 W

Operating temperature

5°C to 35°C (41°F to 95°F) Operating humidity

35% to 85% (no condensation) Storage temperature

–20°C to +60°C (–4°F to +140°F) Storage humidity

10% to 90%

64

Contents

Page THIS APPARATUS MUST BE EARTHED For customers in the USA Declaration of Conformity Disposal of Used Lamp For customers in the United States For customers in Europe For kundene i Norge Trademark Information Page Table of Contents Location of Controls Connections and Preparations Projecting Others On safety On preventing internal heat buildup Caution On repacking Location of Controls Page Page Connections and Preparations Before Setting Up the Projector Improper use Do not do any of the following while using the projector Blocking the ventilation holes (intake or exhaust) Tip Tilting front/rear and left/right Positioning the Projector and a screen When using the 16:9 aspect ratio screen size When using the 4:3 aspect ratio screen size 2 Position the projector so that the lens is parallel to the screen Top view Connecting to a VCR Page To connect to a VCR equipped with the S video connector or video connector Connecting to a Computer Page 2 Press the ?/1 (ON/STANDBY) switch to turn on the projector 3 Turn on the equipment connected to the projector 4 Press INPUT to project the picture on the screen 5 Move both lens shift dials to adjust the picture position To adjust the horizontal position To adjust the vertical position 6 Adjust the picture size using the zoom lever 7 Adjust the focus using the focus ring To adjust the tilt of the installation surface 1 Press MENU 2 Press M/m to select the Setup menu, and press , or 3 Press M/m to select “Language,” and press , or 4 Press M/m/</, to select a language, and press To clear the menu Projecting Turning Off the Power Press WIDE MODE Wide Zoom Normal Full Zoom Full 1 (When a computer signal is input) Full 2 (When a computer signal is input) Notes on selecting the wide screen mode Press one of the PICTURE MODE buttons (DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3) DYNAMIC STANDARD CINEMA 1 Press ADJ PIC 2 Make the setting or adjustment on an item When changing the adjustment level 1 Press RCP on the remote control 2 Press M/m to select “User 1,” “User 2” or “User 3,” then press 3 Select the target color you want to adjust 4 Adjust the color of the specified portions 5 After the adjustment is complete, press Press PIC MUTING Press APA Press FREEZE Using the Menus 2 Press M/m to select a menu item, and press , or ,or 4 Make the setting or adjustment of an item When changing the adjustment level Items that cannot be adjusted To reset the picture that has been adjusted To reset the items that have been adjusted Page Page Page Page Page Page Page Page Page Page Page Page About the Preset Memory No Others Power Picture On-screendisplay Remote control Others Warning Indicators Message Lists Warning messages Caution messages Tools you need to get started: •Projector Lamp LMP-H201(optional) •Standard Phillips screwdriver •Cloth (for scratch protection) 1 Turn off the projector and unplug the AC power cord 6Close the lamp cover, then tighten the screws 7Remove the filter holder 8Remove the air filter 10 Attach the filter holder 11 Wipe dust off the ventilation holes (intake) with a soft cloth 12 Place the project back on its Page Cleaning the lens Cleaning the cabinet Black points and bright points (red, blue, or green) on the screen System Input General Supplied accessories Optional accessories Preset Signals Page Preset memory numbers for each input signal Analog signal Digital signal Input Signals and Adjustable/Setting Items Screen menu Page Page Attaching the PSS-H10projector suspension support Top view Front view Side view