XC-E series

TIMING CHART OF EXTERNAL TRIGGER SHUTTER - MODE 1

(NON-RESET MODE)

For setting the shutter speed using TRG width

HD/VD input

 

 

 

 

 

 

 

 

Mode transition state

 

 

 

 

 

 

 

 

 

External input

External trigger

 

 

 

 

 

 

 

*3 Normal operation

inhibition area

 

 

 

External trigger shutter operation

(50 ms)

shutter operation

 

 

1

 

2

 

 

 

 

3

*1

Trigger

 

 

 

 

 

*3 Trigger

 

 

 

 

 

 

 

 

 

 

*2 Exposure

 

 

*2 Exposure time Te

*2 Exposure time Te

 

 

*1

External HD

 

 

time Te

 

 

 

 

 

 

 

 

*1

External VD

 

 

 

 

 

 

 

 

 

(Continuous

 

 

*

4

 

 

 

 

VD)

 

 

T : T = Under –65 us to +10

s

 

 

EXT-VD

*4

T : T = Under –65 s to +10 s

 

 

 

 

 

 

 

+10 s

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–65 s

 

 

 

 

 

 

 

Video out

 

1

 

2

 

 

 

3

WEN

 

 

 

 

*5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

250H (XC-ES50/ES30, XC-EI50/EI30)

 

 

 

 

 

 

293H (XC-ES50CE/ES30CE, XC-EI50CE/EI30CE)

 

 

 

TRG

 

EXT-VD

 

EXT-VD

65 s

 

 

10 s

Continuous HD/VD input

*1: *2:

*3:

*4:

*5:

This is a signal input from the outside. Be sure to input both HD and VD signals in this case.

Exposure time Te Te = Trigger width + 97 μs (XC-ES50/ES30, XC-EI50/EI30),

Te = Trigger width + 120 μs (XC-ES50CE/ES30CE, XC-EI50CE/EI30CE) (The trigger width should be between 2 μs and 1/4 s)

The normal operation state is engaged when the trigger high period exceeds 1/3sec. The external trigger shutter operation is engaged when the trigger pulse goes “low”. In this case, the area between the falling edge of a trigger pulse and the subsequent 50 ms period is an external trigger input inhibition area. During the trigger inhibit period, an input trigger may be missed.

In all cases the WEN signal indicates when a valid image is available. Normally, an image is output after the external falling edge. If the falling edge of the trigger is very close to the falling edge of the external VD, there may be a delay of 1VD in the output. The period of uncertainty is when the falling edge of VD is between 65 μs before or 10 μs after the falling edge of the trigger.

When the external trigger shutter mode changes into the normal operation mode, one WEN signal is output.

Note : An image is superimposed when the next exposure ends before the previous image is output.

22

Page 24
Image 24
Sony XC-ES50/50CE manual For setting the shutter speed using TRG width, ∙ Continuous HD/VD input