ATX Power | SOYO SY-7IWA-F specification

Hardware Installation

SY-7IWA-F

Warning: Follow these precautions to preserve your Motherboard from any remnant currents when connecting to power supply:

Turn off the power supply and unplug the power cord of the power supply before connecting to PW connector.

This motherboard requires a power supply, that meets the ATX 2.03 specifications. Make sure the power supply can support at least 720mA on the 5V Standby lead.

Please install the ATX power according to the following pin assignment:

ATX Power

12V

5VSB PW-OK GND 5 V GND 5 V GND 3.3V

3.3V

5V

5V -5V

GND

GND

GND Ø Pay special care to the directionality.

PS-ON

GND

-12V 3.3V

38

Image 42

SOYO SY-7IWA-F user manual ATX Power, GND Ø Pay special care to the directionality

Contents

SY-7IWA-F Version SY-7IWA-FEdition August 7IWA-F Serial Table of Contents SY-7IWA-F KEY Features Introduction SY-7IWA-F Electrostatic Discharge Precautions Handling the Motherboard SY-7IWA-F Motherboard Layout Intel SY-7IWA-F Motherboard Components SY-7IWA-F Chipset New design with big benefits SY-7IWA-F Features Benefits Product Highlights Product Package Accelerated Graphics Port A.G.P Universal Serial Bus USB ¿Note IDE Support Serial Ports Real-Time Clock, Cmos SRAM, and BatteryI/O Interface Controller Parallel Port Diskette Drive Controller 4 PS/2 Keyboard and Mouse Interface Audio Subsystem Audio ConnectorCD Line in Connector Hardware Monitor Wake on LAN Technology Chapter Preparations Unpacking the Motherboard Begin the Installation Installation Guide CPU Installation To install the CPU, follow the steps below SY-7IWA-F Sdram Memory Module Installation Hardware Installation Number MemoryModules Double-sided Single-sided Single-sided² RAM Type Motherboard Connector IDE Device Installation HDD, CD-ROM IDE Floppy Drive Installation FDC Power LED & KeyLock Front Panel Connections Reset SpeakerAcpi LED ATX Power On/Off Switch IDE LED Back Panel Connections Parallel Port PRT PS/2 Mouse Universal Serial Bus USB1/USB2 Flat Panel ConnectorVGA monitor connector Onboard Joystick port/audio Other Connections Serial Port COM 1 and COM2 Wake-On-LAN JP44 Pin Assignment Wake-On-LAN WOL Infrared IR1 CD Line-in J10,J11 Cooling Fan Installation CPU Cooling Fan CPU Cooling Fan Cpufan Pin Assignment Power Cooling Fan Chassis Cooling Fan ATX Power Supply AGP VGA Card ATX Power GND Ø Pay special care to the directionality AMR Audio Modem Riser Connector Manual Mode Jumper Setting Set J6 &JP2 to configure CPU FSB FrequencyAuto Mode JP2 Set JP9 for FWH Boot Block Write-Protect Enable/Disable Power-On by Keyboard JP1 Power-On by Win 98 Hot Key USB Keyboard JP11 Setting CPU Core Voltage Adjust JP15, JP16 JP15 Setting JP16 Setting Cmos Clearing JP5 JP5 SettingPower On Cmos Clearing Quick Bios Setup Cmos Setup Utility Copyright C 1984-1999 Award Software Select Soyo Combo Feature Select Standard Cmos SetupSelect Load Optimized Defaults Select Save & Exit Setup Troubleshooting at First Start What should I do if the Motherboard refuses to start? Power Off Selecting items Modifying selected items Function Command Description Save and Exit Setup Exit Without Saving Soyo Combo Setup Soyo Combo Setup Bios Setup Utility Quick CPU Frequency Setup2 L2 Cache Memory System Boot Control Settings Setting Description SmaaSystem Boot Control Settings Boot Other Device AC97 Audio/Modem Setting Description Password Setting DescriptionKB Power on Hot Key Power Standard Cmos Setup Date Time Display Setting Please NoteDate & Time Hard Disks Type & Mode Floppy Drives Setting Description Video Halt On Advanced Bios Features Boot Up Floppy Seek Setting Description Anti VirusFloppy Driver Settings Protection NumLock Setting Description Boot UpSetting Description Gate A20 Status Security Option Other Control OptionsDRAM64MB Advanced Chipset Features Sdram Cycle To-CAS Delay System BiosLatency Time Time Tras/Trc Cache Paging ModeInitial Display CAS# Latency Uart Mode Select Integrated Peripherals IDE Device Controls IDEKeyboard Controls Setting IDE HDD Block Mode FDC Controls Setting Onboard FDCOnboard Serial Setting Description Onboard Parallel Ports Onboard Serial Setting Description Ports UR2 DuplexMode DMA Game Port Address Setting Description Pwron AfterPWR-Fail Midi Port Address Power Management Setup Dpms Power Management Controls IRQ IDE0, IDE1 Reload Global Timer EventsUSB KB FDD, COM PNP/PCI Configuration Setup Reset Setting Description Controls PnP OSInstalled Configuration PNP/PCI Configuration Setup PC Health Status CPU Device Monitoring Pwrfan Speed Vcore, VTT, 3.3V, +5V, +12V, VBAT, 5VSB Load Optimized Defaults Load Optimized Defaults Y/N? Y Load FAIL-SAFE Defaults Load Fail Safe Defaults Y/N? Y Supervisor Password User Password Entering the password IDE HDD Auto Detection Insert the Soyo CD into the CD-ROM drive Soyo CD Start Up Program Menu Install Drivers Read Soyo 7IWA-F ManualManual Selection Menu Intel Whitney VGA Drivers for Win Intel Whitney .inf utility for Win Crystal Codec driver for Win95 Intel Whitney security utility for Win 9x/NT83627hf Winbond Hardware Doctor for Win 95/98 Crystal Wave Synthesizer Enter the Soyo CD Crystal Audio Driver Installation Uninstalling/Re-Installing Crystal Audio Drivers Known Limitations Special Design Considerations Installing Crystal Audio Drivers for Windows NT Uninstalling or Updating Crystal Audio Drivers SY-7IWA-F