Manuals / Speco Technologies / Computer Equipment / Mouse

Speco Technologies KBD-927 D. Set as below in Network menu Set Baud Rate, Dome, 9600, DVR485

Models: KBD-927

1 33

Download 33 pages 38.97 Kb

Page 20

Image 20

D. Set as below in Network menu.

Set Baud Rate

Dome	:	9600
Mux	:	9600
DVR485 :		9600
DVR232 :		9600
Com Ports
Dome	:	Dome
Mux	:	None
DVR485 :		AUX IN
DVR232 :		SDR

4)How to setup SDR

-Switch the SDR on.

-Press the Menu button. Input password according to the instruction. (Factory setting is 4321)

-If the below screen is appeared, set “Quick Setup” to “Off”.

If press OK after putting Quick Setup to off status, the below screen will be appeared. Besides, the below screen will be appeared according to installation status.

Page 20

Image 20

Speco Technologies KBD-927 D. Set as below in Network menu Set Baud Rate, Dome, 9600, DVR485, DVR232, Com Ports, None

Contents

SPECO TECHNOLOGIES KEYBOARD CONTROLLER KBD-927Instruction Manual Rev.040130WARNING AND CAUTION EXPLANATION OF GRAPHICAL SYMBOLSFCC COMPLIANCE STATEMENT CE COMPLIANCE STATEMENTIMPORTANT SAFEGUARDS Table of Contents Chapter 1.0 INTRODUCTION 1.1 Features 1.2 UnpackingChapter 2.0 INSTALLATION 2.1 Connection Diagram 2.2 Dip Switch Setting 2.3 Keyboard Setup1.1 Features INTRODUCITONChapter economic joystick1.2 Unpacking Contents of Keyboard boxKeyboard controller Junction boxINSTALLATION 2.1 Connection Diagram2.1.1 Basic Installation Diagram Chapter2.1.2 Single Multiplexer Figure 3 - Single Multiplexer2.1.3 Single User with Two Multiplexer Figure 4 - Two Multiplexer2.1.4 Two Multiplexer with Slave Keyboard Controller RS-422Figure 8 - Keyboard DIP Switches 2.2 Termination & Dip Switch SettingFigure 7 - Termination and ID Switches 2.3 Multiplexer Control Duplex setupTriplex setup 2.4 Keyboard Setup 2.4 Maser & Slave Keyboard setting Master keyboard should be setup as following procedure1. Check for dip switch the 7th of S2 “OFF” Slave keyboard need to setup as following procedure2.5 Install with ADR series A. Switch the keyboard controller ON B. Input password Factory setting is4 How to setup ADR Switch the ADR on If the below screen is appeared, set “Quick Setup” to “Off”Set “PTZ Device” and “ID” of the dome camera Select “Camera” on the Device menuUnit ID should be 1 up to 99. Unit ID is not allowed number “0” 2.6 Install with SDR series Figure 10 - SDR Connection Diagram4 How to setup SDR Switch the SDR on If the below screen is appeared, set “Quick Setup” to “Off”D. Set as below in Network menu Set Baud Rate DomePTZ set up on the above Setup menu Select TEXT IN/PTZ after PTZ is installed, and then set-up as belowRemote Control Select Camera of Device menu on the above menu2.7 Install with IDR series Figure 11 - IDR Connection DiagramSwitch the IDR on Port COM2 RX Device Fastrax… Baud Rate Data Parity None Stop BitPort COM1 Baud Rate Date Parity None Stop Bit Device ID 8 How to IDR Remote setupIf selects Setup on main menu, the below screen will be appeared 3.1 Keyboard Lock/Unlock Hidden command Single multiplexer configurationTwo multiplexer configurations OPERATIONPicture on Spot output monitor Camera No.1~16+Aux1~4 1+ Main2+ Main 15+ Main3.3 Summary of Keyboard Controls DVR CONTROLMULTIPLEXER Cam001E3.3.1 Keys for Dome camera Key operation example1,2, ... 9,0 e.g., 1+Cam, 3+Tour, 5+Scan, 6+Prst3.3.2 Keys for Multiplexer TwistUp / Down Left / Right3.3.3 Keys for DVR CTRL+1-7,9CTRL + CTRL +No.+ CTRL+ENTR+Joystick CTRL+ENTR+ZoomTrouble Shooting Appendix ASPECIFICATION Appendix B