Manuals / Speco Technologies / Computer Equipment / Mouse

Speco Technologies KBD-927 instruction manual How to IDR Remote setup

Models: KBD-927

1 33

Page 24

If PTZ is not necessary for IDR, cable and installation here is not needed. (IDR is able to be controlled remotely and there’s no PTZ function)

8)How to IDR Remote setup

-If selects Setup on main menu, the below screen will be appeared.

After selecting System and checking Remote control box, please install as below to select Setup remote control. Device ID is not allowed number “0”.

Port : COM1

Baud Rate : 9600

Date : 8

Parity : None

Stop Bit : 1

Device ID : XX

3)Make sure if any change is appeared on screen to press Ctrl + 9 (Next Screen) button of a controller for basic testing. If there’s no change appeared, check cable connection and installation again.

Page 24

Image 24

Speco Technologies KBD-927 How to IDR Remote setup, If selects Setup on main menu, the below screen will be appeared

Contents

SPECO TECHNOLOGIES KEYBOARD CONTROLLER KBD-927Instruction Manual Rev.040130WARNING AND CAUTION EXPLANATION OF GRAPHICAL SYMBOLSFCC COMPLIANCE STATEMENT CE COMPLIANCE STATEMENTIMPORTANT SAFEGUARDS Table of Contents Chapter 1.0 INTRODUCTION 1.1 Features 1.2 UnpackingChapter 2.0 INSTALLATION 2.1 Connection Diagram 2.2 Dip Switch Setting 2.3 Keyboard Setup1.1 Features INTRODUCITONChapter economic joystick1.2 Unpacking Contents of Keyboard boxKeyboard controller Junction boxINSTALLATION 2.1 Connection Diagram2.1.1 Basic Installation Diagram Chapter2.1.2 Single Multiplexer Figure 3 - Single Multiplexer2.1.3 Single User with Two Multiplexer Figure 4 - Two Multiplexer2.1.4 Two Multiplexer with Slave Keyboard Controller RS-4222.2 Termination & Dip Switch Setting Figure 7 - Termination and ID SwitchesFigure 8 - Keyboard DIP Switches Duplex setup Triplex setup2.3 Multiplexer Control 2.4 Keyboard Setup 2.4 Maser & Slave Keyboard setting Master keyboard should be setup as following procedure1. Check for dip switch the 7th of S2 “OFF” Slave keyboard need to setup as following procedure2.5 Install with ADR series A. Switch the keyboard controller ON B. Input password Factory setting is4 How to setup ADR Switch the ADR on If the below screen is appeared, set “Quick Setup” to “Off”Select “Camera” on the Device menu Unit ID should be 1 up to 99. Unit ID is not allowed number “0”Set “PTZ Device” and “ID” of the dome camera 2.6 Install with SDR series Figure 10 - SDR Connection Diagram4 How to setup SDR Switch the SDR on If the below screen is appeared, set “Quick Setup” to “Off”D. Set as below in Network menu Set Baud Rate DomePTZ set up on the above Setup menu Select TEXT IN/PTZ after PTZ is installed, and then set-up as belowRemote Control Select Camera of Device menu on the above menu2.7 Install with IDR series Figure 11 - IDR Connection DiagramSwitch the IDR on Port COM2 RX Device Fastrax… Baud Rate Data Parity None Stop Bit8 How to IDR Remote setup If selects Setup on main menu, the below screen will be appearedPort COM1 Baud Rate Date Parity None Stop Bit Device ID 3.1 Keyboard Lock/Unlock Hidden command Single multiplexer configurationTwo multiplexer configurations OPERATIONPicture on Spot output monitor Camera No.1~16+Aux1~4 1+ Main2+ Main 15+ Main3.3 Summary of Keyboard Controls DVR CONTROLMULTIPLEXER Cam001E3.3.1 Keys for Dome camera Key operation example1,2, ... 9,0 e.g., 1+Cam, 3+Tour, 5+Scan, 6+Prst3.3.2 Keys for Multiplexer TwistUp / Down Left / Right3.3.3 Keys for DVR CTRL+1-7,9CTRL + CTRL +No.+ CTRL+ENTR+Joystick CTRL+ENTR+ZoomTrouble Shooting Appendix ASPECIFICATION Appendix B