Manuals / Speco Technologies / Computer Equipment / Mouse

Speco Technologies KBD-927 instruction manual Single User with Two Multiplexer

Models: KBD-927

1 33

Page 10

2.1.3 Single User with Two Multiplexer

POWER	POWER	POWER
AC 24V	AC 24V	AC 24V

AWG # 24

BNC

1ST MAIN MONITOR

AL1	AC+ AC- FGND (RX+)	(RX-)	RX+(TX+) RX-(TX-) GND AC- AC+	AL5
AL2				AL6
GND				GND
AL3				AL7
AL4				AL8
GND				GND
COM1				COM3
NC1				NC3
NO1				NO3
COM2				COM4
NC2	(RS-422)			NC4
NO2	(RX+)	(RX-)	RX+(TX+) RX-(TX-)	NO4
	(RX+)	(RX-)	RX+(TX+) RX-(TX-)
			RS-485

SPOT MONITOR

2ND MAIN MONITOR

BNC

1ST MULTIPLEXER	2ND MULTIPLEXER
	RS-485(+) PIN No.4
	RS-485(-) PIN No.5

Spot output of the first multiplexer to be connected to 16th input of the second multiplexer.

And first spot output of the 2nd multiplexer to be connected to the spot monitor. You will see the picture of the selected camera (1~31) on spot monitor by selecting camera No.+Cam.

Figure 4 – Two Multiplexer

Page 10

Image 10

Speco Technologies KBD-927 instruction manual Single User with Two Multiplexer

Contents

Instruction Manual SPECO TECHNOLOGIES KEYBOARD CONTROLLERKBD-927 Rev.040130WARNING AND CAUTION EXPLANATION OF GRAPHICAL SYMBOLSFCC COMPLIANCE STATEMENT CE COMPLIANCE STATEMENTIMPORTANT SAFEGUARDS Chapter 2.0 INSTALLATION Table of Contents Chapter 1.0 INTRODUCTION1.1 Features 1.2 Unpacking 2.1 Connection Diagram 2.2 Dip Switch Setting 2.3 Keyboard SetupChapter 1.1 FeaturesINTRODUCITON economic joystickKeyboard controller 1.2 UnpackingContents of Keyboard box Junction box2.1.1 Basic Installation Diagram INSTALLATION2.1 Connection Diagram Chapter2.1.2 Single Multiplexer Figure 3 - Single Multiplexer2.1.3 Single User with Two Multiplexer Figure 4 - Two Multiplexer2.1.4 Two Multiplexer with Slave Keyboard Controller RS-422Figure 7 - Termination and ID Switches 2.2 Termination & Dip Switch SettingFigure 8 - Keyboard DIP Switches Triplex setup Duplex setup2.3 Multiplexer Control 2.4 Keyboard Setup 1. Check for dip switch the 7th of S2 “OFF” 2.4 Maser & Slave Keyboard settingMaster keyboard should be setup as following procedure Slave keyboard need to setup as following procedure2.5 Install with ADR series 4 How to setup ADR Switch the ADR on A. Switch the keyboard controller ONB. Input password Factory setting is If the below screen is appeared, set “Quick Setup” to “Off”Unit ID should be 1 up to 99. Unit ID is not allowed number “0” Select “Camera” on the Device menuSet “PTZ Device” and “ID” of the dome camera 2.6 Install with SDR series Figure 10 - SDR Connection DiagramD. Set as below in Network menu Set Baud Rate 4 How to setup SDR Switch the SDR onIf the below screen is appeared, set “Quick Setup” to “Off” DomeRemote Control PTZ set up on the above Setup menuSelect TEXT IN/PTZ after PTZ is installed, and then set-up as below Select Camera of Device menu on the above menu2.7 Install with IDR series Figure 11 - IDR Connection DiagramSwitch the IDR on Port COM2 RX Device Fastrax… Baud Rate Data Parity None Stop BitIf selects Setup on main menu, the below screen will be appeared 8 How to IDR Remote setupPort COM1 Baud Rate Date Parity None Stop Bit Device ID Two multiplexer configurations 3.1 Keyboard Lock/Unlock Hidden commandSingle multiplexer configuration OPERATION2+ Main Picture on Spot output monitor Camera No.1~16+Aux1~41+ Main 15+ MainMULTIPLEXER 3.3 Summary of Keyboard ControlsDVR CONTROL Cam001E1,2, ... 9,0 3.3.1 Keys for Dome cameraKey operation example e.g., 1+Cam, 3+Tour, 5+Scan, 6+PrstUp / Down 3.3.2 Keys for MultiplexerTwist Left / RightCTRL + 3.3.3 Keys for DVRCTRL+1-7,9 CTRL +Joystick No.+CTRL+ENTR+ CTRL+ENTR+ZoomTrouble Shooting Appendix ASPECIFICATION Appendix B