Manuals / Speco Technologies / Computer Equipment / Mouse

Speco Technologies KBD-927 Select Camera of Device menu on the above menu, RS232/TEXT IN, Parity

Models: KBD-927

1 33

Download 33 pages 38.97 Kb

Page 21

Image 21

Select Camera of Device menu on the above menu.

PTZ set up on the above Setup menu

Select TEXT IN/PTZ after PTZ is installed, and then set-up as below

RS232/TEXT IN	Baud Rate	Parity	Data	Stop	Usage

RS232	9600	None	8	1	Remote Control

TEXT IN/PTZ	9600	None	8	1	PTZ Control

1)After installing Camera, and RS232 & TEXT IN/PTZ setup, the installation with dome camera is basically completed. Please refer to manual of SDR for the other installation.

2)Press the related number of a controller which correspondent to unit ID of SDR. Then press DVR button and adjust unit ID of a controller. Unit ID is not allowed number “0”.

3)Make sure if any change is appeared on screen to press button of a controller for basic testing. If there’s no change appeared, check cable connection and installation again.

Page 21

Image 21

Speco Technologies KBD-927 Select Camera of Device menu on the above menu, PTZ set up on the above Setup menu, Baud Rate

Contents

KBD-927 SPECO TECHNOLOGIES KEYBOARD CONTROLLERInstruction Manual Rev.040130EXPLANATION OF GRAPHICAL SYMBOLS WARNING AND CAUTIONCE COMPLIANCE STATEMENT FCC COMPLIANCE STATEMENTIMPORTANT SAFEGUARDS 1.1 Features 1.2 Unpacking Table of Contents Chapter 1.0 INTRODUCTIONChapter 2.0 INSTALLATION 2.1 Connection Diagram 2.2 Dip Switch Setting 2.3 Keyboard SetupINTRODUCITON 1.1 FeaturesChapter economic joystickContents of Keyboard box 1.2 UnpackingKeyboard controller Junction box2.1 Connection Diagram INSTALLATION2.1.1 Basic Installation Diagram ChapterFigure 3 - Single Multiplexer 2.1.2 Single MultiplexerFigure 4 - Two Multiplexer 2.1.3 Single User with Two MultiplexerRS-422 2.1.4 Two Multiplexer with Slave Keyboard Controller2.2 Termination & Dip Switch Setting Figure 7 - Termination and ID SwitchesFigure 8 - Keyboard DIP Switches Duplex setup Triplex setup2.3 Multiplexer Control 2.4 Keyboard Setup Master keyboard should be setup as following procedure 2.4 Maser & Slave Keyboard setting1. Check for dip switch the 7th of S2 “OFF” Slave keyboard need to setup as following procedure2.5 Install with ADR series B. Input password Factory setting is A. Switch the keyboard controller ON4 How to setup ADR Switch the ADR on If the below screen is appeared, set “Quick Setup” to “Off”Select “Camera” on the Device menu Unit ID should be 1 up to 99. Unit ID is not allowed number “0”Set “PTZ Device” and “ID” of the dome camera Figure 10 - SDR Connection Diagram 2.6 Install with SDR seriesIf the below screen is appeared, set “Quick Setup” to “Off” 4 How to setup SDR Switch the SDR onD. Set as below in Network menu Set Baud Rate DomeSelect TEXT IN/PTZ after PTZ is installed, and then set-up as below PTZ set up on the above Setup menuRemote Control Select Camera of Device menu on the above menuFigure 11 - IDR Connection Diagram 2.7 Install with IDR seriesPort COM2 RX Device Fastrax… Baud Rate Data Parity None Stop Bit Switch the IDR on8 How to IDR Remote setup If selects Setup on main menu, the below screen will be appearedPort COM1 Baud Rate Date Parity None Stop Bit Device ID Single multiplexer configuration 3.1 Keyboard Lock/Unlock Hidden commandTwo multiplexer configurations OPERATION1+ Main Picture on Spot output monitor Camera No.1~16+Aux1~42+ Main 15+ MainDVR CONTROL 3.3 Summary of Keyboard ControlsMULTIPLEXER Cam001EKey operation example 3.3.1 Keys for Dome camera1,2, ... 9,0 e.g., 1+Cam, 3+Tour, 5+Scan, 6+PrstTwist 3.3.2 Keys for MultiplexerUp / Down Left / RightCTRL+1-7,9 3.3.3 Keys for DVRCTRL + CTRL +CTRL+ENTR+ No.+Joystick CTRL+ENTR+ZoomAppendix A Trouble ShootingAppendix B SPECIFICATION