Manuals / Star Micronics / Computer Equipment / Printer

Star Micronics 347F user manual Control Panel

Models: 347F

1 63

Download 63 pages 30.59 Kb

Page 13

3.CONTROL PANEL

3.CONTROL PANEL

1 “ON LINE” switch

Switches the printer between “ON LINE” and “OFF LINE”. When- ever the printer switches between “ON LINE” and “OFF LINE”, the

buzzer gives one short beep (“ON LINE” and “OFF LINE” switching is possible only when the paper is loaded in the printer.)

2 “FEED” switch

∙ When this switch is pressed and then released within 0.5 sec., the paper feeds one line.

∙ When this switch is depressed for

Fig. 3-1 Control panelmore than 0.5 sec., the paper feeds continuously.

(The above paper feed operation is possible for both “ON LINE” and “OFF LINE” modes.)

3“POWER” lamp (green LED)

∙Lights when the power for the printer is on. 4 “ALARM” lamp (red LED)

∙Lights when the paper is out.

If the paper is out, load a new roll then press the “ON LINE” switch.

∙Flashes when the front cover is open or a mechanical error (motor lock etc.) occurs. The buzzer will give one short beep followed by a long beep. Mount the front cover properly and press the “ON LINE” switch. If the buzzer still sounds and the “ALARM” lamp flashes, this signifies that a mechanical error has occurred. Locate the cause of the error and turn the power for the printer off and back on again to reset the printer.

(In case of a mechanical error, the data will not be cleared even if the power is turned off.)

5“ON LINE” lamp (green LED) LED lit: Printer is ON LINE LED off: Printer is OFF LINE

LED flashes: Validation printing mode is set.

When all lamps 3to 5light simultaneously and the buzzer sounds continu- ously, a CPU error has occurred. In case of a CPU error, turn off the power then turn it on again. When turning off the power, the data will be cleared.

ENGLISH

– 11 –

Image 13

Star Micronics 347F user manual Control Panel

Contents

DOT MATRIX PRINTER SP317/347FUSERS MANUAL GUIDE D’UTILISATION BEDIENUNGSANLEITUNG MANUALE DI ISTRUZIONI∙ The contents of this manual are subject to change without notice EC Council Directive 89/336/EEC of 3 MayFederal Communications Commission Radio Frequency Interference Statement1-1. SP317 TABLE OF CONTENTSSP347 LOADING THE PAPER1-1. SP317 1. LOADING THE RIBBON CARTRIDGE1-2. SP347 Page 2-1. SP317 2. LOADING THE PAPER6 Turn the power switch on the printer to the on position Fig. 2-5 Removing the rear cover SP347 2-2. SP347Fig. 2-8 Roll paper guide SP347 Fig. 2-6 Position of the adjust lever SP347Fig. 2-9 Raise the auto cutter SP347 Fig. 2-7 Mounting the roll paper holders SP3477 Turn the power switch on the printer to the on position 2-3. Removing the Roll Paper 3. CONTROL PANEL Page L’appendice n’est pas traduit TABLE DES MATIÈRES1-1. SP317 1. INSTALLATION D’UNE CARTOUCHE DE RUBANd’arrêt 1-2. SP347OK NON 2-1. SP317 2. CHARGEMENT DU PAPIERFig. 2-2 Montage des attaches pour rouleau de papier SP317 6 Mettez le commutateur d’alimenta Fig. 2-5 Dépose du cache arrière SP347 2-2. SP347Cache arrière Hors tensiontement SP347 Fig. 2-6 Positionnement du levier d’ajusFig. 2-7 Fixation des attaches pour rouleau de papier SP347d’empêcher l’alimentation cor- recte du papier de marche 8 Coupez l’extrémité du papier en veillant à couper droitA Insérez ensuite l’axe pour rouleau Fig. 2-10 Chargement du papier SP3472-3. Enlèvement d’un rouleau de papier 3. PANNEAU DE COMMANDE Page EINLEGEN DER FARBBANDKASSETTE INHALTSVERZEICHNIS1-1. SP317 1. EINLEGEN DER FARBBANDKASSETTEAbb. 1-3 Abnehmen der Frontabdeckung SP347 1-2. SP347Abb. 1-4 Die automatische Abschneideinheit anheben, und das Verpackungsmaterial entfernen SP347NEI N 2-1. SP317 2. EINLEGEN DES PAPIERShinten drücken 6 Den Netzschalter des Druckers in Ein-Stellung stellen Abb. 2-5 Abnehmen der Rückabdeckung SP347 2-2. SP347Rückabdeckung Netzschalter aus∙ Indem Sie den Sicherungsring ein Papierführung ein. Lassen Sie einenAbschneideinheit an, und stellen Sie sie in senkrechte Stellung wie in der7 Den Netzschalter des Druckers in Ein-Stellung stellen C Ziehen Sie die Kante des Papiers- tau, um Schlaufen zu beseitigen 3. BEDIENFELD Page L’Appendice appare solo nella sezione in inglese di questo manuale INDICE1-1. SP317 1. CARICAMENTO DELLA CARTUCCIA DEL NASTROFig. 1-3 Rimozione del coperchio anteriore SP347 1-2. SP347Coperchio anteriore Spegnere Taglierina automatica Materiale di imballaggioFig. 1-5 Caricamento della cartuccia del nastro SP347 OKNO2-1. SP317 2. CARICAMENTO DELLA CARTA5 Regolare le guide della carta sini- stra e destra Fig. 2-5 Rimozione del coperchio poste riore SP347 2-2. SP347Supporto carta in rotolo regolazione SP347 Fig. 2-6 Posizione della leva diFig. 2-8 Guida della carta in rotolo SP347 Fig. 2-9 Sollevare la taglierina automatica SP347possibile 2-3. Rimozione della carta in rotolo 3. PANNELLO DI CONTROLLO Page Connectors and Signals Serial Interface APPENDIXSerial interface connector RS-232CRS-422A option 20 mA current loop optionAPPENDIX Example of interface connections for an IBM PC Interface Connections Serial InteffaceAPPENDIX This connector mates with an Amphenol 57-30360 connector Connectors and Signals Parallel InterfaceParallel interface connector printer side APPENDIXDrive output 24V, max. 1.0 A Peripheral Unit Drive CircuitAPPENDIX Drive circuitDot Alignment Adjust Mode To reset the printing status, meaning to return the specified position to the default position the fourth printing status from the top, press the FEED button while holding down the ONLINE button General Specifications Note The paper must not be glued to the core AC power cable 169 W × 330 D × 176 H mm Approx 4.6 kg Overall dimensions mm SP347APPENDIX P 1996.01 P MEMOSTAR MICRONICS DEUTSCHLAND GMBH OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INCHEAD OFFICE