Manuals / Star Micronics / Computer Equipment / Printer

Star Micronics 347F user manual 2-2. SP347, 5 Removing the rear cover SP347

Models: 347F

1 63

Download 63 pages 30.59 Kb

Page 9

2-2. SP347

2-2. SP347

Rear cover

Power off

1Turn the power switch on the printer to the off position.

2To remove the front cover lift it up approx. 3cm. and pull it forward.

NOTE: Do not touch the print head immediately after printing as it can be extremely hot.

3To remove the rear cover lift it up approx. 3cm and push it backwards.

ENGLISH

Fig. 2-5 Removing the rear cover (SP347)

4Adjust DIP switch 2-4, the roll paper holder and the adjust lever position according to the width and thickness of the roll paper that is being used.

∙Refer to Installation Manual in regard to the position of the DIP switch.

∙If you do not know the standard position of the adjust lever, lower the adjust lever as far as it will go (on the rear cover side), and then pull it two positions. That position is standard position A.

	Paper		DIP switch 2-4	Adjust lever	Roll paper holder
	Paper width	Thickness	(Fig. 4-1)	position (Fig. 2-6)	(Fig. 2-7)

	2.25 inches	1 sheet of paper	OFF	A	Used (Inner groove)

		Printer paper	OFF	B	Used (Inner groove)
		Printer paper	OFF	B	Used (Inner groove)

	3.0 inches	1 sheet of paper	ON	A	Used (Outer groove)

		Printer paper	ON	B	Used (Outer groove)
		Printer paper	ON	B	Used (Outer groove)

	3.25 inches	1 sheet of paper	ON	A	Not used

		Printer paper	ON	B	Not used
		Printer paper	ON	B	Not used

– 7 –

Image 9

Star Micronics 347F user manual 2-2. SP347, 5 Removing the rear cover SP347

Contents

DOT MATRIX PRINTER SP317/347FUSERS MANUAL GUIDE D’UTILISATION BEDIENUNGSANLEITUNG MANUALE DI ISTRUZIONI∙ The contents of this manual are subject to change without notice EC Council Directive 89/336/EEC of 3 MayFederal Communications Commission Radio Frequency Interference Statement1-1. SP317 TABLE OF CONTENTSSP347 LOADING THE PAPER1-1. SP317 1. LOADING THE RIBBON CARTRIDGE1-2. SP347 Page 2-1. SP317 2. LOADING THE PAPER6 Turn the power switch on the printer to the on position Fig. 2-5 Removing the rear cover SP347 2-2. SP347Fig. 2-8 Roll paper guide SP347 Fig. 2-6 Position of the adjust lever SP347Fig. 2-9 Raise the auto cutter SP347 Fig. 2-7 Mounting the roll paper holders SP3477 Turn the power switch on the printer to the on position 2-3. Removing the Roll Paper 3. CONTROL PANEL Page L’appendice n’est pas traduit TABLE DES MATIÈRES1-1. SP317 1. INSTALLATION D’UNE CARTOUCHE DE RUBANd’arrêt 1-2. SP347OK NON 2. CHARGEMENT DU PAPIER 2-1. SP317Fig. 2-2 Montage des attaches pour rouleau de papier SP317 6 Mettez le commutateur d’alimenta Fig. 2-5 Dépose du cache arrière SP347 2-2. SP347Cache arrière Hors tensiontement SP347 Fig. 2-6 Positionnement du levier d’ajusFig. 2-7 Fixation des attaches pour rouleau de papier SP347d’empêcher l’alimentation cor- recte du papier de marche 8 Coupez l’extrémité du papier en veillant à couper droitA Insérez ensuite l’axe pour rouleau Fig. 2-10 Chargement du papier SP3472-3. Enlèvement d’un rouleau de papier 3. PANNEAU DE COMMANDE Page EINLEGEN DER FARBBANDKASSETTE INHALTSVERZEICHNIS1-1. SP317 1. EINLEGEN DER FARBBANDKASSETTEAbb. 1-3 Abnehmen der Frontabdeckung SP347 1-2. SP347Abb. 1-4 Die automatische Abschneideinheit anheben, und das Verpackungsmaterial entfernen SP347NEI N 2. EINLEGEN DES PAPIERS 2-1. SP317hinten drücken 6 Den Netzschalter des Druckers in Ein-Stellung stellen Abb. 2-5 Abnehmen der Rückabdeckung SP347 2-2. SP347Rückabdeckung Netzschalter aus∙ Indem Sie den Sicherungsring ein Papierführung ein. Lassen Sie einenAbschneideinheit an, und stellen Sie sie in senkrechte Stellung wie in der7 Den Netzschalter des Druckers in Ein-Stellung stellen C Ziehen Sie die Kante des Papiers- tau, um Schlaufen zu beseitigen 3. BEDIENFELD Page L’Appendice appare solo nella sezione in inglese di questo manuale INDICE1-1. SP317 1. CARICAMENTO DELLA CARTUCCIA DEL NASTROFig. 1-3 Rimozione del coperchio anteriore SP347 1-2. SP347Coperchio anteriore Spegnere Taglierina automatica Materiale di imballaggioFig. 1-5 Caricamento della cartuccia del nastro SP347 OKNO2-1. SP317 2. CARICAMENTO DELLA CARTA5 Regolare le guide della carta sini- stra e destra 2-2. SP347 Fig. 2-5 Rimozione del coperchio poste riore SP347Supporto carta in rotolo regolazione SP347 Fig. 2-6 Posizione della leva diFig. 2-8 Guida della carta in rotolo SP347 Fig. 2-9 Sollevare la taglierina automatica SP347possibile 2-3. Rimozione della carta in rotolo 3. PANNELLO DI CONTROLLO Page Connectors and Signals Serial Interface APPENDIXSerial interface connector RS-232C20 mA current loop option RS-422A optionAPPENDIX Interface Connections Serial Intefface Example of interface connections for an IBM PCAPPENDIX This connector mates with an Amphenol 57-30360 connector Connectors and Signals Parallel InterfaceParallel interface connector printer side APPENDIXDrive output 24V, max. 1.0 A Peripheral Unit Drive CircuitAPPENDIX Drive circuitDot Alignment Adjust Mode To reset the printing status, meaning to return the specified position to the default position the fourth printing status from the top, press the FEED button while holding down the ONLINE button General Specifications Note The paper must not be glued to the core AC power cable Overall dimensions mm SP347 169 W × 330 D × 176 H mm Approx 4.6 kgAPPENDIX P 1996.01 P MEMOOVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC STAR MICRONICS DEUTSCHLAND GMBHHEAD OFFICE