Sterling 90-225 CFM, SDA 150-380 Mode, Parameter, Setting range, Factory, setting

Level 1		AL-2 Alarm Value 2		-1999 to 9999 EU			0	25.0
Level 1		AL-3 Alarm Value 3		-1999 to 9999 EU			0	Default
Level 1		P Proportional Band		0.1 to 999.9% FS			10.0	4.4
Level 1		I Integral Time		0 to 3999 SEC			233	84
Level 1		d Derivative Timer		0 to 3999 SEC			40	13
Level 1		C-SC Cooling		0.01 to 99.99			1.00	Default
		Coefficient
Level 1		C-db Dead Band		-19.99 to 99.99%FS			0.00	Default
Level 1		6F-r Manual Reset		0.0 to 100.0%			50.0	Default
		Value
Level 1		HYS Hysteresis (Heat)		0.01 to 99.99%FS			0.10	Default
Level 1		CHYS Hysteresis (Cool)		0.01 to 99.99%FS			0.10	Default
Level 1		CP Control Period		1 to 99 SEC			20	Default
		(Heat)
Level 1		C-CP Control Period		1 to 99 SEC			20	Default
		(Cool)
Mode		Parameter			Setting range	Default		Factory
								setting
Level 2		r-L Remote/Local			RMT/LCL		LCL	Default
Level 2		SPrU Sp Ramp Time Unit			M(Minutes)/H(Hours)		M	Default
Level 2		SPrE Sp Ramp Set Value			0 to 9999 EU		0	Default
Level 2		LbA LBA Detection Time			0 to 9999 SEC		0	Default
Level 2		Au-5 MV at Stop			-5.0 to 105.0%		0.0	Default
Level 2		Au-E MV at PV Error			-5.0 to 105.0%		0.0	Default
Level 2		6L-L MV Upper Limit			MV Lower Limit +0.1 to 105.0%		105.0	Default
Level 2		6L-L MV Lower Limit			-5.0 to MV Upper Limit –0.1%		-5.0	Default
Level 2		6rL MV Change Rate Limit			0.0 to 100.0%/SEC		0.0	Default
Level 2		CnF Input Digital Filter			0 to 9999 SEC		0	Default
Level 2		ALH1 Alarm 1 Hysteresis			0.01 to 99.99%		0.02	Default
Level 2		ALH2 Alarm 2 Hysteresis			0.01 to 99.99%		0.02	Default
Level 2		ALH3 Alarm 3 Hysteresis			0.01 to 99.99%		0.02	Default
Level 2		Cn5H Input Shift Upper			-199.9 to 999.9 °C		0.0	Default
		Limit
Level 2		Cn5L Input Shift Lower			-999.9 to 999.9 °C		0.0	Default
		Limit
Mode	Parameter				Setting range		Default	Factory
								setting
Setup	Cn-E Input Type		0 to 21				2	3
Setup	Cn-H Scaling Upper		Scaling Lower Limit +1 to 9999 EU				-100	Default
		Limit
Setup	Cn-L Scaling Lower		-1999 to SP Setting Upper Limit -0.1 EU				0	Default
		Limit
Setup	dP Decimal Point		0 to 3				0	Default
Setup	d-U °C/F Selection		°C/F				°C	°F
Setup	CnCE Parameter		Yes/No				No	Default

Cabinet Series Dehumidifying Dryer 43