Process Heater Box Assembly | Sterling SDA AP-1 specification

1.Remove the bolts securing the process heater access cover.

2.Sketch the heater wiring configuration so the heaters may be re-wired properly. Heaters are mounted on a common plate of three or six for easy maintenance.

3.Remove the jumper bars and wires for the heater plate assembly(ies) being removed or replaced.

4.Remove the bolts securing the heater plate assembly and slide out the assembly. Avoid damaging the gaskets.

5.Remove individual heaters for replacement by removing the large brass nuts and washers.

6.Re-install the heaters and heater plate assemblies in reverse order, replacing gaskets if necessary.

Caution! Heater loops should not touch each other. "Hot spots" will lead to premature heater failure.

7.Re-install the jumper wires and bars according to the sketch made earlier.

8.Re-secure the process heater access cover.

Figure 16: Process Heater Box Assembly			Stainless Steel
			Heater Housing
	High		Cover
	Temperature	Heater Elements
	Gasket	Heater Elements
	Gasket	Double Wall
		Double Wall
		Stainless Steel
		Heater
Heater Elements		Housing
		High
Heater Element		Temperature
Mounting Plate		Gasket
		Heater Element
		Mounting Plate
	Double Wall
	Stainless Steel
	Heater
	Housing
	High
	Temperature
Heater Assembly	Gasket
Heater Assembly
Gude Bars			Heater Assembly
Stainless Steel			Gude Bars
Stainless Steel
Heater Housing
Cover
Hex Nut For	Heater Element
Securing the Heater	Mounting Hex Nut
Wire	High Temperature	Heater Element
	High Temperature	Heater Element
Washer	Washer / Gasket
Heater Wire with
Crimped on Closed
Loop Connector
Heater Mounting	Heater Element	Heater Assembly
Heater Mounting	Bulkhead Fitting	Guide Bar
Plate

Replacing the Regeneration Heater (Electric Dryers)

The regeneration heaters are wired in the delta formation, mounted in the core of the desiccant tanks.

DANGER! Disconnect and lock out power before heater replacement.

Large Dehumidifying Dryers

Maintenance

62

Image 62

Sterling SDA AP-1 specifications Process Heater Box Assembly, Replacing the Regeneration Heater Electric Dryers

Contents

SDA Large AP-1 Control Dehumidifying Dryer Event of Shipping Damage Shipping InfoUnpacking and Inspection If the Shipment is Not Complete Returns Table of Contents Operation Troubleshooting Safety Symbols Used in this Manual SafetyHow to Use This Manual Dryer Safety Tags Description Operator Responsibility ResponsibilityGeneral Responsibility Maintenance Responsibility Reporting a Safety Defect General Description Functional DescriptionModels Covered in This Manual Process/Regeneration Cycle Sequence of Operation Mechanical Features Standard FeaturesAuto Start Timer Electrical Features Closed-Loop Regeneration OptionsDewpoint Extend Drawings and Diagrams Optional dryer dust collector Process Air Dust Collector Aftercooler Design SpecificationsProcess Aftercooler Process Air Dust Collector Recommended Temperature Settings Material Overdrying Protection Controller Options Mechanical OptionsElectrical Options Safety Device Lock-Outs Safety Devices and InterlocksSafety Circuit Standards Fail Safe OperationPage Dimensions and Specifications Denotes availability Mechanical Options Denotes availability Denotes availability Rigging and Placing Unit Mechanical InstallationUncrating the Equipment Making Electrical Connections Making Gas Line Connections Gas-Fired Models Only Description Checking for Proper Blower Rotation Checking Blower Rotation Making Dryer/Drying Hopper Process Air Connections Dryer/Drying Hopper Process Air Connections Process Air Heater on Drying Hopper Large Dehumidifying Dryers Mechanical Installation Connecting Aftercooler/Precooler Cooling Water Optional Aftercooler Components & Flow Rates Using the Drying Hopper Air Trap Drying Hopper Air Trap Controls Controller Description Process Air Temperature and Conveying Process Controller Dryer Status Screen Startup Screen Main Menu Screen Dryer Alarms Help System LOG OFFIdentifying Controller Screens Setting Values Auto Start Main Menu Dryer Status Dryer Setup Over DRY Protect Alarms Auto TuneDryer Menu Dryer Setup Screen 4 Dryer Setup Screen 2Dryer Setup Screen 3 Overdry Protection Screen 2 Overdry ProtectionOverdry Protection Screen 1 Process AutoTune Screen Alarm History ScreenAutotune Autostart Timer Screen DEW Point SetupDew Point Setup Screen Auto Start Help Menu Screen System Setup SET Clock Hour Meters Alarm History StatusHelp Menu System Menu LOW Level Detection Setup System Backup Service Menu Main Menu System SetupSystem Setup Screen Clock Menu Screen Autostart Clock Screen Input Status Screen Hour Meter ScreenInput Status Output Status Service Menu Screen System Backup ScreenService Alarm Screens Redundant Safety Controller Display Alarm Screen Example Setting the Redundant Safety Controller Always put your set point to 30F above set point Large Dehumidifying Dryers Controls Operation Start-up Using the Dryer Status Screen Alarms Alarm Descriptions Shutdown Photocopy this page for your maintenance records MaintenanceMaintenance Schedule Preventative Maintenance Cleaning or Replacing the Process Air Filters Cleaning or Replacing the Regeneration Filter Calibrating the Dirty Filter Alarm Checking the Dewpoint Control System Replacing the Desiccant Corrective MaintenanceSymptoms of Worn Out Desiccant Desiccant Tower Assembly Replacing the Process Heater Electric Dryers Process Heater Box Assembly Replacing the Regeneration Heater Electric Dryers Regeneration Heater Box Assembly Introduction TroubleshootingBasic Troubleshooting Large Dehumidifying Dryers Troubleshooting Using a Platinum Resistance Thermometer Determining Temperature Controller Errors or Sensor ErrorsUsing a Thermocouple Returned Material Policy Warranty ReturnsAppendix Credit Returns Technical Specifications Annex B Information Spare Parts List Level 3 Mechanical Components Dryer Identification Serial Number Tag Located on back of Dryer Parts Department Service DepartmentTechnical Assistance Sales Department