Manuals / Sterling / Kitchen Appliance / Food Processor

Sterling operating instructions SSE-2 2.1. For your safety, Safety instructions, General

Models: SSE-2

1 58

Download 58 pages 63.95 Kb

Page 11

SSE-2

SSE-2

2.1. For your safety

General

The operating personnel of this equipment must be at least 16 years old.

Please read these operating instructions carefully before taking into operation for the first time. Contact us should questions arise. This avoids injury and damage to equipment!

These operating instructions must be kept available at all times at the place of operation of the equipment. Improper operation results in danger of accidents!

Please note that, for reasons of clarity, not all conceivable cases regarding operation or mainten- ance of the equipment can be covered in these operating instructions.

Please observe all safety instructions and warnings on the equipment. This avoids injury and da- mage to equipment!

All work on the equipment is to be carried out by persons whose qualifications are specified in the pertaining chapters of the operating instructions. Improper operation results in danger of acci- dents!

The proper working clothes are to be worn during any work on the equipment. This avoids injury!

The local regulations and requirements pertaining to this equipment must be observed.

Disconnect electrical components from the mains supply before work is carried out on these com- ponents Caution: Danger to life through electrical shock!

Compile detailed operating instructions based on these Operating instructions for the sequence of procedures to be carried out on this equipment. Improper operation results in danger of acci- dents!

Please note that sound levels exceeding 85 db(A) may in the long term damage your health. Use the appropriate ear muffs. This avoids impairment of hearing!

SM4-615

Safety instructions 2-2

Image 11

Sterling operating instructions SSE-2 2.1. For your safety, Safety instructions, General

Contents

SM4-615 Sterling Material ProcessingOperating Instructions Single Conveyor Unit SSE-2 P/N882.00608.00Telephone: 800 Edition: 07/02 Technical serviceSSE-2 Sterling Material Processing SSE-2 Sales and Contracting Department Parts and Service DepartmentSSE-2 Table of contentsSSE-2 SSE-2 1. General instructionsGeneral instructions General instructions SSE-2 1.1. Warnings and symbols1.5. Notes on usage SSE-2 1.2. Explanations and information1.3. Legal basis 1.4. Fields of applicationsSSE-2 2. Safety instructionsSafety instructions General SSE-2 2.1. For your safetySafety instructions SSE-2 Safety instructionsAssembly Operation Safety instructionsMaintenance SSE-2SSE-2 2.2. For the operating safety of the equipmentSafety instructions SSE-2 3. Putting into operationPutting into operation Putting into operation SSE-2 3.1. Checking the pipe systemIf the conditions points 3 + 4 are met SSE-2 3.2. Adjusting the suction pipesPutting into operation If the conditions points 3 + 4 are not metThe conveying capacity is too low SSE-2 3.3. Setting the controllerSetting the conveying time Putting into operationSSE-2 3.5. Switching off the unit3.4. Initial conveying operations Setting the line clear timeSSE-2 4. Error and error correctionError and error correction SSE-2 Error and error correctionThe following error messages can be displayed “E1 SSE-2 Error and error correctionSSE-2 5. MaintenanceMaintenance SSE-2 MaintenancePlease observe the maintenance intervals Maintenance SSE-2 5.1. Maintenance intervals5.2. Servicing the conveyor SSE-2 MaintenanceC B A SSE-2 5.2.2. Adjusting the flap switchMaintenance or optional, active cleaning SSE-2 5.2.3. Cleaning the unitMaintenance SSE-2 MaintenanceMaintenance SSE-2 5.3. Replacing carbon brushes at turbineObserve that no cables will be squeezed MaintenanceSSE-2 SSE-2 6. Functional descriptionFunctional description Functional description SSE-2 6.1. GeneralFunctional description SSE-2 6.2. ControllerOptional SSE-2Functional description SSE-2 7. Transport, Assembly and StorageTransport, Assembly and Storage Transport, Assembly and Storage 7.2. AssemblySSE-2 7.1. Transport and Packing 7.3. StorageSSE-2 8. Assembly instructionsAssembly instructions Assembly instructions SSE-2 8.1. AssemblySSE-2 Assembly instructionsAssembly SM4-615 A material hopper VT 1,0 is required SSE-2 8.2. Mounting on the processing machine8.3. Mounting onto a machine hopper Assembly instructionsA material hopper VT 1,0 is required 8.5. Mounting onto dosing station DTAssembly instructions SSE-2Assembly instructions SSE-2 8.6. Material feed8.7. Mounting the suction pipe MV Assembly instructions SSE-2 8.8. Pipework8.9. Electrical connection SSE-2 Assembly instructionsX5 = Flap switch X6 = acknowledgement key Assembly instructionsTerminals X2 = Power supply X4 = Blower X5 = Cleaning X6 = Clearing X9 = Alarm X3 = PESSE-2 8.11. Installing the accessoriesAssembly instructions SSE-2 9. Technical dataTechnical data SSE-2 Basic Version Technical dataOptional Features SSE-2SM4-615 Technical dataDimension Sheet SSE-2SM4-615 10. Spare parts listSpare parts list SSE-2SM4-615 Spare parts listSSE-2 SSE-2,230 V, 50 Hz / 110 V, 60 HzOrder no 10.1. SSE-2,230 V, 50 HzSpare parts list SSE-2SSE-2 10.2. SSE-2,110 V, 60 HzSpare parts list SSE-2 10.3. SSE-2,230 V, 50 Hz with active cleaning10.4. SSE-2,110 V, 60 Hz with active cleaning Spare parts listSM4-615 SSE-2 10.5. AccessoriesSpare parts list Please observe the operating manuals in chapterSSE-2 11. AccessoriesAccessories SSE-2 12. Electrical manualElectrical manual