Sunfire TGR401, TGR-401-230 manual FM and AM Tuner Operation, Changing Modes, Saving Presets

CHAPTER 5

FM and AM Tuner Operation

The supplied AM and FM antennas must be connected to the TGR-401 antenna terminals, or no stations will be tuned.

The internal AM and FM tuners are selected either by pressing Input and rotating the manual selector on the front panel, or by touching the AM or FM buttons in the remote’s TGR-401 page 2. The front panel display will change to show the frequency of the last station you were listening to.

The FM tuner can tune stations from 87.5 MHz to 108.0 MHz in 0.2 MHz steps (.05 MHz steps for some international models). The AM tuner range is 530 kHz to 1710 kHz in 10 kHz steps (531 kHz to 1710 kHz in 9 kHz steps for some international models).

1.Press the remote's MAIN button to make sure the display is on the main display menu.

2.Press the TG401 de-

vice button to set the remote to operate your TGR-401. The display changes to show the TGR-401 input selections.

3. Press PAGE to reach page 2. This allows selection of the SIRIUS tuner, FM and AM tuner, TNMOD and SCAN.

TNMOD lets you use the number keys

either to enter the station frequen- cy directly, or to enter the preset station number. TNMOD is also available in Zone 2.

SCAN lets you scan up to the next tunable station. It will remain there for 5 seconds before scanning up to the next station. Press the Navigation SEL button to select a the currently-playing station.

46

ONOFF

ZONE 2

TGR401

MAIN

PAGE	MAIN	FAV
PAGE
	MUTE	PREV
		CH
VOL		CH	CH UP/DOWN
	GUIDE
MENU			INFO
MENU	INFO	EXIT
NAV UP
MODE	SEL		MODE
NAV DOWN			NAV SELECT
1	2	3
4	5	6	NUMBER KEYS
7	8	9
+10	0	ENT

4.Various remote buttons also oper- ate the AM and FM tuner:

•NAVIGATION KEYPAD - multifunc- tional for setup menu navigation and AM/FM tuning.

•NAV UP - Tunes up one frequency step at a time. If you hold it down, it will scan up to the next station.

•NAV DOWN - Tunes down one fre- quency step at a time. If you hold it down, it will scan down to the next available station.

•NAV SELECT - Select a station.

•INFO - Show the current station frequency and preset number, or the listening mode.

•MENU - Enter the OSD Setup menu where FM and AM presets can be con gured.

•CH UP/DOWN - Tunes up and down through preset list. The list is created in the preset menu within the setup menu.

•NUMBER KEYS - These allow you to enter the actual frequency of the station directly. If you press TN- MOD, you can enter station preset numbers instead.

5. To operate FM/AM in Zone 2, select the Zone 2 button, then Zone 2's rst page will show the FM/AM input selectors.

Changing Modes

1.Press the INFO button until the front panel display shows the cur- rent surround mode. Then use the mode buttons to select a mode.

Saving Presets

The OSD preset menu is used to enter the preset number and frequen- cy of your favorite radio stations.

MAIN MENU

TRIMS

TONE CONTROLS

MODES

PRESETS

SETUP

PRESETS

AM/FM

SIRIUS

AM/FM	FREQ	CHOICES
PRESETS
01 FM	107.50	AM/FM, FREQ/NONE
02 FM	98.30
03 FM	99.90
04 AM	1230
05 AM	610
06 NONE
.
40 NONE

SIRIUS	CHANNEL	CHOICES
PRESETS
01	1	1–223/NONE
02	223
03	NONE
04	NONE

05NONE

.

40NONE

1.In the AM/FM preset menu, press the remote's center navi- gation select (SEL) to choose AM or FM, or reset a preset to NONE.

2.Use the navigation up or down to move to the preset number, for example, preset 01.

User's Manual