Watching TV, Selecting a desired channel | Sylvania 6900DTD manual

Basic Operation

Watching TV

STB is capable of receiving analog (NTSC format) and digital (ATSC format) broadcasts.

All available channels from any of these broadcast sources can be tuned in using the CH o/p buttons and number buttons on your remote control.

Each channel number consists of a main channel number and a sub-channel number.

1Turn the TV on and select the input to which the STB is connected to.

2Turn the STB on.

•The power indicator on the STB front panel will blink and light up.

Remote:

2

3

3

3

3

3 Selecting a desired channel.

When using CH o/p buttons:

•Press CH o button to tune a higher channel number.

•Press CH p button to tune a lower channel number.

TIP:

Be sure to complete AUTOSCAN in SETUP WIZARD or in the SETUP menu so that STB receives all channels available to be watched (ATSC and NTSC).

30

EN

1A23

Image 30

Sylvania 6900DTD owner manual Watching TV, Selecting a desired channel, When using CH o/p buttons

Contents

6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Information on digital broadcasting Receives bothAtsc and Ntsc Hdtv Major features of STBAtsc Ntsc Remote control sensor Power buttonPower indicator Setup button Rear Panel Remote Control Snap the battery cover back AccessoriesInstalling batteries Remote controller unit and AA batteries x2 Part No. NE120UD Reference to Setup menu Setup Wizard Channel Display Clock Detail When Connecting to Cable BOX Also Connections to antennaCable BOX Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Connections STB connection to a standard stereo system Stereo Component Connections STB connection to a decoder with Dolby Digital Digital Decoder VCR Initial setup Setup Wizard will appearSetup Wizard 1/8 will appear STB starts scanning channels Setup Wizard 3/8 will appearButtons, then press Enter To skip the scanning Setup Wizard 5/8 will appear Refer to Information on Time Zones on Press Enter when the cursor is on SET When not using the auto-clock settingSelect OFF on the channel map, then press Enter 26-1 Press Enter When using CH o/p buttons Watching TVSelecting a desired channel When using number buttons E.g., entering 26-1 TV-Y 1800 1830 1900 1930 2000 Press Info to display a channel banner When tuning in a channel from NtscChannel banner Press Info to clear DTV Lock Audio map Only when tuning in Atsc Choosing audio Language When tuning in Atsc When tuning in NtscSequence will repeat as shown below when available Press Audio button Press any button to quit Picture StillPress Still o button while watching During STILL, the programs audio will continue Scanning No SignalOn screen messages Restricted Program Press EPG button while watching TV EPG will appear on the screen Select the desired program using o / p Navigation buttons When going back to the previousWhen selecting a program being broadcast Components of Electronic Program Guide EPG CC Closed Caption Setup menu for preference Adding channels Press Setup to display Setup menuWhen adding the digital channel ADD/ Delete To add, first enter the digital channel Select Channel using o / p navigationButtons, then press Enter Number Channel menu will appear Information on Channel Map Select ADD using o / p navigation buttons, then press EnterPress Setup to exit Setup menu To continue adding Delete Deleting channelsYou can add and delete channels in the channel map To delete the digital channel Cursor will move to the channel map Digital channel number 26 will be deleted Press Enter when the cursor is on the digital channelWill be indicated in the box at the top of the screen To continue deleting Antenna Adjusting antennaWhen adjusting the digital channel Channel 26-1 will be tuned When adjusting other channels continuously Adjust the antenna direction to get the best receptionReceiving the signal strength of the channel Antenna menu will appear, then STB starts Receiving channels Autoscan Select Next using s / B navigation buttons, then press Enter Autoscan is complete To cancel Autoscan during scanningWhen no Signal appears on the screen Verify the antenna connection, then complete Selecting screen formats Screen RatioDisplay menu will appear Screen ratio should be selected to fit your TV screen Press Enter to exit Setup menuScreen ratio options will appear Screen ratio will be set Display Mode STB Display mode will be setInformation on 43 TV 43 TV Full Letter BoxZoom Sidebar Setting the clock Clock menu will appear Daylight savings time setting menu will appear Time Zone setting menu will appear Pacific AlaskaHawaii Mountain Current time setting menu will appear Your settings will be activated Activated 4,5,6 Will become black on the channel map Select OFF from the channel-map, then press EnterChannel search completed. will be indicated Setting a new password Detail menu will appear Chip / CC Quit Channel Display Clock Detail Password setting menu will appear Your new password is storedCHIP/CC menu will appear Setting for V-CHIP/CC CHIP/CC CHIP/CC password window will appear Enter your 4-digit password When choosing STBcontrols V-CHIP RatingsWhen choosing TVcontrols V-CHIP Ratings Press Setup to exit Setup menu Setting Mpaa rating Mpaa Rating Press Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies Setting TV rating TV Rating Press Setup to display Setup menu TV rating setting menu will appear Information on TV ratings Quit Channel Selecting CC options CC Selection Enter your 4-digit password CC options menu will appear Serve as the preferred data channelsSelected CC option will be set Choosing the screen language Menu Language Then press Enter Language menu will appear Troubleshooting Using coaxial digital Symptom RemedyAudio problems when With weak signal Specifications Glossary and Acronyms DST Mpaa Ubicación de los controles Nota Instalación de las pilas Conexiones de antena AL Conectar EL Equipo a UNA Caja Para Cable Conexión del STB a un Sdtv utilizando la salida Video Configuración inicial Presione Enter NuméricosCuando el cursor se encuentre en SET, presione Enter Si no desea usar la función de ajuste automático de reloj Limited Warranty