Current time setting menu will appear | Sylvania 6900DTD specification

Advanced Operation

7 Select MANUAL using o / p navigation buttons, then press ENTER.

•The current time setting menu will appear.

CLOCK

8Enter YEAR, DATE, and TIME using o / p / s / B navigation buttons or number

buttons.

•Press ENTER to set each value, then the cursor will move to the next.

•When going back and forth, press s / B navigation buttons to move the cursor.

QUIT

CHANNEL

DISPLAY

CLOCK

DETAIL

Enter current time.

YEAR 2002

DATE 1 31 THU

TIME 2 50 PM

SET

CLOCK

QUIT

CHANNEL

DISPLAY

CLOCK

DETAIL

Enter current time.

YEAR 2002

DATE 3 31 SUN

TIME

1 52 PM

SET

NOTE:

After all information is entered, the cursor will move to SET.

TIP:

To enter the YEAR, enter the last 2 digits of the year. The year will be entered. (e.g., Enter “03” using number buttons; 2003 will be shown.)

62

EN

1A23

Image 62

Sylvania 6900DTD owner manual Current time setting menu will appear

Contents

6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Atsc and Ntsc Information on digital broadcastingReceives both Hdtv Major features of STBAtsc Ntsc Remote control sensor Power buttonPower indicator Setup button Rear Panel Remote Control Snap the battery cover back AccessoriesInstalling batteries Remote controller unit and AA batteries x2 Part No. NE120UD Reference to Setup menu Setup Wizard Channel Display Clock Detail Cable BOX When Connecting to Cable BOX AlsoConnections to antenna Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Connections STB connection to a standard stereo system Stereo Component Connections STB connection to a decoder with Dolby Digital Digital Decoder VCR Setup Wizard 1/8 will appear Initial setupSetup Wizard will appear STB starts scanning channels Setup Wizard 3/8 will appearButtons, then press Enter To skip the scanning Setup Wizard 5/8 will appear Refer to Information on Time Zones on Select OFF on the channel map, then press Enter Press Enter when the cursor is on SETWhen not using the auto-clock setting 26-1 Press Enter Selecting a desired channel When using CH o/p buttonsWatching TV When using number buttons E.g., entering 26-1 TV-Y 1800 1830 1900 1930 2000 Press Info to display a channel banner When tuning in a channel from NtscChannel banner Press Info to clear DTV Lock Audio map Only when tuning in Atsc Choosing audio Language When tuning in Atsc When tuning in NtscSequence will repeat as shown below when available Press Audio button Press any button to quit Picture StillPress Still o button while watching During STILL, the programs audio will continue Scanning No SignalOn screen messages Restricted Program Press EPG button while watching TV EPG will appear on the screen When selecting a program being broadcast Select the desired program using o / p Navigation buttonsWhen going back to the previous Components of Electronic Program Guide EPG CC Closed Caption Setup menu for preference Adding channels Press Setup to display Setup menuWhen adding the digital channel ADD/ Delete To add, first enter the digital channel Select Channel using o / p navigationButtons, then press Enter Number Channel menu will appear Information on Channel Map Select ADD using o / p navigation buttons, then press EnterPress Setup to exit Setup menu To continue adding Delete Deleting channelsYou can add and delete channels in the channel map To delete the digital channel Cursor will move to the channel map Digital channel number 26 will be deleted Press Enter when the cursor is on the digital channelWill be indicated in the box at the top of the screen To continue deleting Antenna Adjusting antennaWhen adjusting the digital channel Channel 26-1 will be tuned When adjusting other channels continuously Adjust the antenna direction to get the best receptionReceiving the signal strength of the channel Antenna menu will appear, then STB starts Receiving channels Autoscan Select Next using s / B navigation buttons, then press Enter Autoscan is complete To cancel Autoscan during scanningWhen no Signal appears on the screen Verify the antenna connection, then complete Display menu will appear Selecting screen formatsScreen Ratio Screen ratio should be selected to fit your TV screen Press Enter to exit Setup menuScreen ratio options will appear Screen ratio will be set Display Mode STB Display mode will be setInformation on 43 TV 43 TV Full Letter BoxZoom Sidebar Setting the clock Clock menu will appear Daylight savings time setting menu will appear Time Zone setting menu will appear Pacific AlaskaHawaii Mountain Current time setting menu will appear Your settings will be activated Activated 4,5,6 Channel search completed. will be indicated Will become black on the channel mapSelect OFF from the channel-map, then press Enter Setting a new password Detail menu will appear Chip / CC Quit Channel Display Clock Detail CHIP/CC menu will appear Password setting menu will appearYour new password is stored Setting for V-CHIP/CC CHIP/CC CHIP/CC password window will appear When choosing TVcontrols V-CHIP Ratings Enter your 4-digit passwordWhen choosing STBcontrols V-CHIP Ratings Press Setup to exit Setup menu Setting Mpaa rating Mpaa Rating Press Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies Setting TV rating TV Rating Press Setup to display Setup menu TV rating setting menu will appear Information on TV ratings Quit Channel Selecting CC options CC Selection Enter your 4-digit password Selected CC option will be set CC options menu will appearServe as the preferred data channels Choosing the screen language Menu Language Then press Enter Language menu will appear Troubleshooting Using coaxial digital Symptom RemedyAudio problems when With weak signal Specifications Glossary and Acronyms DST Mpaa Ubicación de los controles Nota Instalación de las pilas Conexiones de antena AL Conectar EL Equipo a UNA Caja Para Cable Conexión del STB a un Sdtv utilizando la salida Video Configuración inicial Presione Enter NuméricosCuando el cursor se encuentre en SET, presione Enter Si no desea usar la función de ajuste automático de reloj Limited Warranty