Connections to antenna, Cable BOX | Sylvania 6900DTD instruction

Connections

Connections to antenna

Use a standard antenna cable to connect the wall jack to the ANT IN Jack on STB.

STB connection to the antenna

NOTE:

Antenna and antenna cable are not included.

To the antenna

Rear panel of STB

WHEN CONNECTING TO CABLE BOX ALSO:

NOTE:

	Incoming cable
	signals
	CABLE BOX
To the antenna	ANT	ANT
	IN	OUT

Antenna, antenna cable and Cable box are not included.

TV

ANT-IN

Jack

Antenna cable

STB

ANT. IN

1Use a standard antenna cable to connect the wall jack to the ANT IN Jack on STB.

NOTE:

Refer to the following pages for the connection to TV.

2Use an incoming cable to connect to an antenna input jack on the cable box.

3Use a standard antenna cable to connect an antenna output jack on the cable box to an antenna input jack on the TV.

4After completing the connection to TV, plug the AC power cord of the TV into the AC outlet, then turn the TV on.

5Select the output channel from the cable box e.g., ch3 or ch 4.

NOTE:

Refer to the TV owner’s manual for further information.

6Plug the AC power cord of STB into the AC outlet, then turn STB on.

Refer to following pages for the connection to TV.

Note to the Cable TV System Installer :

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.

16

EN

1A23

Image 16

Sylvania 6900DTD owner manual Connections to antenna, When Connecting to Cable BOX Also

Contents

6900DTD Table of Contents Important Safeguards S2 8 9 8 a Precautions Receives both Information on digital broadcastingAtsc and Ntsc Major features of STB AtscHdtv Ntsc Power button Power indicatorRemote control sensor Setup button Rear Panel Remote Control Accessories Installing batteriesSnap the battery cover back Remote controller unit and AA batteries x2 Part No. NE120UD Reference to Setup menu Setup Wizard Channel Display Clock Detail Connections to antenna When Connecting to Cable BOX AlsoCable BOX Right Connections to other devices Connections Connections STB connection using S-VIDEO output to Sdtv Connections STB connection using Video output to Sdtv Connections STB connection to a standard stereo system Stereo Component Connections STB connection to a decoder with Dolby Digital Digital Decoder VCR Setup Wizard will appear Initial setupSetup Wizard 1/8 will appear Setup Wizard 3/8 will appear Buttons, then press EnterSTB starts scanning channels To skip the scanning Setup Wizard 5/8 will appear Refer to Information on Time Zones on When not using the auto-clock setting Press Enter when the cursor is on SETSelect OFF on the channel map, then press Enter 26-1 Press Enter Watching TV When using CH o/p buttonsSelecting a desired channel When using number buttons E.g., entering 26-1 TV-Y 1800 1830 1900 1930 2000 When tuning in a channel from Ntsc Channel bannerPress Info to display a channel banner Press Info to clear DTV Lock Audio map Only when tuning in Atsc Choosing audio Language When tuning in Ntsc Sequence will repeat as shown below when availableWhen tuning in Atsc Press Audio button Picture Still Press Still o button while watchingPress any button to quit During STILL, the programs audio will continue No Signal On screen messagesScanning Restricted Program Press EPG button while watching TV EPG will appear on the screen When going back to the previous Select the desired program using o / p Navigation buttonsWhen selecting a program being broadcast Components of Electronic Program Guide EPG CC Closed Caption Setup menu for preference Press Setup to display Setup menu When adding the digital channelAdding channels ADD/ Delete Select Channel using o / p navigation Buttons, then press Enter NumberTo add, first enter the digital channel Channel menu will appear Select ADD using o / p navigation buttons, then press Enter Press Setup to exit Setup menuInformation on Channel Map To continue adding Deleting channels You can add and delete channels in the channel mapDelete To delete the digital channel Cursor will move to the channel map Press Enter when the cursor is on the digital channel Will be indicated in the box at the top of the screenDigital channel number 26 will be deleted To continue deleting Adjusting antenna When adjusting the digital channelAntenna Channel 26-1 will be tuned Adjust the antenna direction to get the best reception Receiving the signal strength of the channelWhen adjusting other channels continuously Antenna menu will appear, then STB starts Receiving channels Autoscan Select Next using s / B navigation buttons, then press Enter To cancel Autoscan during scanning When no Signal appears on the screenAutoscan is complete Verify the antenna connection, then complete Screen Ratio Selecting screen formatsDisplay menu will appear Press Enter to exit Setup menu Screen ratio options will appearScreen ratio should be selected to fit your TV screen Screen ratio will be set Display Mode Display mode will be set Information on 43 TVSTB 43 TV Letter Box ZoomFull Sidebar Setting the clock Clock menu will appear Daylight savings time setting menu will appear Time Zone setting menu will appear Alaska HawaiiPacific Mountain Current time setting menu will appear Your settings will be activated Activated 4,5,6 Select OFF from the channel-map, then press Enter Will become black on the channel mapChannel search completed. will be indicated Setting a new password Detail menu will appear Chip / CC Quit Channel Display Clock Detail Your new password is stored Password setting menu will appearCHIP/CC menu will appear Setting for V-CHIP/CC CHIP/CC CHIP/CC password window will appear When choosing STBcontrols V-CHIP Ratings Enter your 4-digit passwordWhen choosing TVcontrols V-CHIP Ratings Press Setup to exit Setup menu Setting Mpaa rating Mpaa Rating Press Setup to display Setup menu Mpaa rating setting menu will appear When you want to block all PG-13 movies Setting TV rating TV Rating Press Setup to display Setup menu TV rating setting menu will appear Information on TV ratings Quit Channel Selecting CC options CC Selection Enter your 4-digit password Serve as the preferred data channels CC options menu will appearSelected CC option will be set Choosing the screen language Menu Language Then press Enter Language menu will appear Troubleshooting Symptom Remedy Audio problems whenUsing coaxial digital With weak signal Specifications Glossary and Acronyms DST Mpaa Ubicación de los controles Nota Instalación de las pilas Conexiones de antena AL Conectar EL Equipo a UNA Caja Para Cable Conexión del STB a un Sdtv utilizando la salida Video Configuración inicial Numéricos Cuando el cursor se encuentre en SET, presione EnterPresione Enter Si no desea usar la función de ajuste automático de reloj Limited Warranty