TANDBERG PrecisionHD 1080p/720p camera | Camera User Guide |
Contentsontents
IntroductionIntroduction
PhysicalPhysicaliinterfacet rf
Cablesables
ConnectiConnect toto codec
Videoideo forformatsats
Daisyaisy chainingchaining
AppendicesApp dicesices
Contactontact usus
The VISCA™/RS–232 control protocol, cont...
Camera commands
Command |
| Command Packet | Comments | |
Power_On | 8x | 01 04 00 02 ff | Power control. This command | |
Power_Off | 8x | 01 04 00 03 ff | stores the zoom and focus value | |
and reset these motors. Used for | ||||
|
|
| ||
|
|
| Tiger if the camera was on for a | |
|
|
| long time. | |
Video_Format | 8x | 01 35 0p 0q 0r ff | Selects video format. p = | |
|
|
| reserved. q = video mode. r = | |
|
|
| See the chapter about the DIP | |
|
|
| switch settings | |
WB_Auto | 8x | 01 04 35 00 FF | WB: White Balance | |
WB_Table_Manual | 8x | 01 04 35 06 ff |
| |
WB_Table_Direct | 8x | 01 04 75 0p 0q 0r 0s ff | Used if WBmode = Table manual | |
|
|
| pqrs = wb table. | |
AE_Auto | 8x | 01 04 39 00 FF | AE: Automatic Exposure. | |
AE_Manual | 8x | 01 04 39 03 FF |
| |
Iris_Direct | 8x | 01 04 4B 0p 0q 0r 0s FF | Used if AE mode = Manual. pqrs: | |
|
|
| Iris position, range 0..50 | |
Gain_Direct | 8x | 01 04 4c 0p 0q 0r 0s FF | Used if AE mode = Manual. pqrs: | |
|
|
| Gain position, | |
Backlight_On | 8x | 01 04 33 02 FF | BacklightCompensation mode | |
Backlight_Off | 8x | 01 04 33 03 FF |
| |
Mirror_On | 8x | 01 04 61 02 ff | Sony calls this CAM_LR_Reverse. | |
Mirror_Off | 8x | 01 04 61 03 ff | RR (FT/AT mirror command) | |
| ||||
Flip_On | 8x | 01 04 66 02 ff | Sony calls this CAM_ImgFlip. | |
Flip_Off | 8x | 01 04 66 03 ff |
| |
Gamma_Auto | 8x | 01 04 51 02 ff | Gamma mode. Default uses | |
Gamma_Manual | 8x | 01 04 51 03 ff | gamma table 4. | |
| ||||
Gamma_Direct | 8x | 01 04 52 0p 0q 0r 0s ff | pqrs: Gamma table to use in | |
|
|
| manual mode. Range |
Command |
| Command Packet | Comments | |
MM_Detect_On | 8x | 01 50 30 01 ff | Turn on the Motor Moved | |
|
|
| Detection (camera recalibrates if | |
|
|
| touched) | |
MM_Detect_Off | 8x | 01 50 30 00 ff | Turn off the Motor Moved | |
|
|
| Detection (camera does not | |
|
|
| recalibrate if touched) | |
Call_LED_On | 8x | 01 33 01 01 ff | Refers to orange LED on top | |
Call_LED_Off | 8x 01 33 01 00 ff | of camera. Will always be off at | ||
startup. | ||||
Call_LED_Blink | 8x | 01 33 01 02 ff | ||
| ||||
Power_LED_On | 8x | 01 33 02 01 ff | Green power LED. If switched to | |
Power_LED_Off | 8x | 01 33 02 00 ff | off and stored to startup profile, it | |
will always be off. | ||||
|
|
| ||
IR_Output_On | 8x | 01 06 08 02 ff | See IR push message. | |
IR_Output_Off | 8x | 01 06 08 03 ff |
| |
IR_CameraControl_On | 8x | 01 06 09 02 ff | Lets up/down/left/right/zoom+/- | |
IR_CameraControl_Off | 8x | 01 06 09 03 ff | on the IR remote control the | |
camera directly. Those keycodes | ||||
|
|
| ||
|
|
| will be sent to the controller if IR | |
|
|
| Output is on. | |
23 | www.tandberg.com |
