Manuals / Technicolor - Thomson / Computer Equipment / Switch

Technicolor - Thomson Cable Terminal Information, TS 870 TRANSFER SWITCH, Connection Tightness

Models: TS 870

1 46

Download 46 pages 24.5 Kb

Page 31

15.CABLE TERMINAL INFORMATION

TS 870 TRANSFER SWITCH

15.CABLE TERMINAL INFORMATION

CONNECTION TIGHTNESS

TERMINAL RATING

(In-lbs)

BASIC MODEL

QTY

TERMINAL

MOUNTING

CABLE

PER

RANGE

SCREW

CLAMP

PHASE

TS 87xA-0100

1

#14-1/0

120

50

TS 87xA-0150

1

#2–4/0

120

120

TS 87xA-0200

1

#6–350MCM

150

275

TS 87xA-0250

1

#6–350MCM

150

275

TS 87xA-04001

2

2/0–500MCM

72

275

TS 87xA-06001

2

2/0–500MCM

72

275

TS 87xA-08001

3

2/0–500MCM

110

375

TS 87xA-12001

4

4/0–500MCM

375

375

1.Optional terminal ratings are available in some models – Consult Thomson Technology.

2.For other model types not shown, contact Thomson Technology for further information.

16.REQUIREMENTS FOR UPSTREAM CIRCUIT PROTECTIVE DEVICES

16.1.WITHSTAND CURRENT RATINGS (ALL MODELS WITHOUT INTEGRAL

OVERCURRENT PROTECTION OPTION)

RATED

WITHSTAND CURRENT RATING AMPS (RMS) 1

BASIC MODEL

MAX.

CURRENT

With Upstream Circuit Breaker Protection

With Upstream Fuse Protection

VOLTAGE

(A)

@240V

@480V

@600V

@ Up to 600V

Fuse Type

TS87xA-0100

600

100

65,000

25,000

18,000

100,000

T, J

TS87xA-0150

TS87xA-0200

TS87xA-0250

TS87xA-0400

TS87xA-0600

TS87xA-0800

TS87A-1000/1200

600

240

600

600

600

600

600

150

200

250

400

600

800

1000/1200

65,000

65,000

65,000

65,000

65,000

65,000

65,000

25,000

N/A

35,000

50,000

50,000

50,000

50,000

18,000

N/A

25,000

35,000

35,000

35,000

42,000

100,000

N/A

100,000

100,000

100,000

100,000

100,000

T, J

T, J

T, J

T, J

T, J

Consult Factory

Consult Factory

1.Standard ratings only are shown. Consult Thomson Technology for versions with higher withstand current ratings.

2.For other model types not shown, contact Thomson Technology for further information.

Fuse ratings shown are maximum allowable to permit use of the transfer switch in application with available fault current not exceeding that shown. Consideration must be given to fuse sizing when fuses also provide overload protection.

PM062 REV 5 08/05/05

27

Thomson Technology

Image 31

Technicolor - Thomson TS 870 Cable Terminal Information, Requirements For Upstream Circuit Protective Devices, In-lbs

Contents

PM062 Rev 5 08/05/05 AUTOMATIC TRANSFER SWITCHESINSTALLATION, OPERATING SERVICE MANUAL 9087A - 198th Street, Langley, BC Canada V1M 3B1 Telephone 604Page TRANSFER SWITCH MECHANISM - 100A-800A, S STYLE TABLE OF CONTENTSNOTES TO INSTALLER GENERAL NOTES ON SERVICING TRANSFER SWITCH MECHANISMGROUND FAULT SITE TEST REQUIREMENTS TRANSFER SWITCH MECHANISM -1000A-1200A, T-STYLERECOMMENDED MAINTENANCE CONNECTION CONFIGURATION OPTIONSto change without notice Operating & Service Manual Version1. PRODUCT REVISION HISTORY 2. EQUIPMENT STORAGEDANGER Arc Flash and Shock Hazard. Will cause severe injury or death 3. NOTES TO INSTALLER3.1. UPSTREAM CIRCUIT PROTECTIVE DEVICES/ELECTRICAL CONNECTIONS Do not open equipment until ALL power sources are disconnected3.3. TRANSFER SWITCHES WITH MULTI-TAP VOLTAGE CAPABILITY 3.2. TRANSFER SWITCHES WITH INTEGRAL OVER CURRENT PROTECTIONcoordination. Failure to do so may result in equipment failure 3.4. SYSTEM PHASING-HIGH LEG DELTA SYSTEMS VOLTAGE ON TS870 SERIES TRANSFER SWITCHES WITH TSC4. GENERAL DESCRIPTION 3.5. REMOTE START CONTACT FIELD WIRING3.6. DIELECTRIC TESTING 3.7. INSTALLATION OF OPEN TYPE TRANSFER SWITCHESUtility to indicate the source of primary power Thomson Technology 4.1. PRODUCT MODEL CODETS 870 TRANSFER SWITCH PM062 REV 5 08/05/055.1.1. NORMAL OPERATION 4.2. TYPICAL COMMISSIONING PROCEDURES5.1. STANDARD AUTOMATIC TRANSFER SWITCH 5. GENERAL THEORY OF OPERATION5.2.1. NORMAL OPERATION 5.2. SERVICE ENTRANCE AUTOMATIC TRANSFER SWITCH5.2.2. OVER CURRENT TRIP Close and lock the transfer switch enclosure door 5.2.3. SERVICE DISCONNECT PROCEDUREbefore connecting power sources Do not open equipment until ALL power sources are disconnected 5.2.4. ADDITIONAL PROCEDURESDANGER Arc Flash and Shock Hazard. Will cause severe injury or death Failure to move the mechanism to the Neutral Position may result in serious personal injury or death due to electrical shock 6. OVER CURRENT PROTECTION 6.1. STANDARD TS 870 AUTOMATIC TRANSFER SWITCH5.3. TEST MODES Page Do not open equipment until ALL power sources are disconnected 7. GENERAL NOTES ON SERVICING TRANSFER SWITCH MECHANISMDANGER Arc Flash and Shock Hazard. Will cause severe injury or death No moisture or other contamination is present DANGER Arc Flash and Shock Hazard. Will cause severe injury or death 8. TRANSFER SWITCH MECHANISM - 100A-800A, S Style8.1. MANUAL OPERATION Do not open equipment until ALL power sources are disconnectedAutomatic operation may be regained by replacing the control circuit isolation plug. With all sources of power de-energized to the transfer switch, the control circuit isolation plug can be re-connected. The drive system will operate the transfer switch to the required position. See manual operation instruction on front of transfer switch mechanism DANGER Arc Flash and Shock Hazard. Will cause severe injury or death 9. TRANSFER SWITCH MECHANISM -1000A-1200A, T-Style9.1. MANUAL OPERATION Do not open equipment until ALL power sources are disconnectedPM062 REV 5 08/05/05 TS 870 TRANSFER SWITCHThomson Technology Do not open equipment until ALL power sources are disconnected 10. RECOMMENDED MAINTENANCEDANGER Arc Flash and Shock Hazard. Will cause severe injury or death PM062 REV 5 08/05/05 TS 870 TRANSFER SWITCHThomson Technology PM062 REV 5 08/05/05 TS 870 TRANSFER SWITCHThomson Technology ØC ØB ØA N TS 870 TRANSFER SWITCHPM062 REV 5 08/05/05 Thomson TechnologyPM062 REV 5 08/05/05 TS 870 TRANSFER SWITCHThomson Technology Thomson Technology 14. CONNECTION CONFIGURATION OPTIONSTS 870 TRANSFER SWITCH PM062 REV 5 08/05/05TS 870 TRANSFER SWITCH 15. CABLE TERMINAL INFORMATION16. REQUIREMENTS FOR UPSTREAM CIRCUIT PROTECTIVE DEVICES 16.1. WITHSTAND CURRENT RATINGS ALL MODELS WITHOUT INTEGRAL16.2. INTERRUPTING CAPACITY CURRENT RATINGS ALL MODELS WITH 17. GROUND FAULT SITE TEST REQUIREMENTS17.1. PERFORMANCE TEST The interconnected system shall be evaluated to ensure compliance with the appropriate schematic drawings. The proper location of sensors and power cabling shall be determined. The grounding points of the system shall be verified to determine that ground paths do not exist that would bypass the sensors. The use of high-voltage testers and resistance bridges may be required. A simulated fault current is to be generated by a coil around the sensors. The reaction of the circuit-interrupting device is to be observed for correct response. The results of the test are to be recorded on the test form provided DANGER Arc Flash and Shock Hazard. Will cause severe injury or death 18. TROUBLESHOOTINGDo not open equipment until ALL power sources are disconnected TS 870 TRANSFER SWITCHNo time delay when there should be TS 870 TRANSFER SWITCHpower failure in the utility source when it shouldComments 19. REPLACEMENT PARTSComponent Description Thomson TechnologyComments 20. PRODUCT RETURN POLICYComponent Description Thomson TechnologyThomson Technology 21. NOTESTS 870 TRANSFER SWITCH PM062 REV 5 08/05/0522. PERFORMANCE TEST FORM Page Do not open equipment until ALL power sources are disconnected TYPICAL AUTOMATIC TRANSFER SWITCHCOMMISSIONING PROCEDURES Model Series TS APPENDIX “A”2 Check for mechanical damage shipping or installer Final CommissioningTYPICAL AUTOMATIC TRANSFER SWITCH COMMISSIONING PROCEDURES Model Series TSiii Green “Load” LED is “ON” TYPICAL AUTOMATIC TRANSFER SWITCHCOMMISSIONING PROCEDURES Model Series TS APPENDIX “A”20 Ensure copies of manuals for the equipment are on site TYPICAL AUTOMATIC TRANSFER SWITCHCOMMISSIONING PROCEDURES Model Series TS APPENDIX “A”Do not open equipment until ALL power sources are disconnected SWITCHES WITH TSC 80 CONTROLLERAPPENDIX “B” INSTRUCTIONS TO CHANGE SYSTEM VOLTAGE ON TS 870 SERIES TRANSFER600V SWITCHES WITH TSC 80 CONTROLLERAPPENDIX “B” INSTRUCTIONS TO CHANGE SYSTEM VOLTAGE ON TS 870 SERIES TRANSFER