Manuals / Technicolor - Thomson / Computer Equipment / Switch

Technicolor - Thomson TS 870 Replacement Parts, Component Description, Thomson Technology

Models: TS 870

1 46

Download 46 pages 24.5 Kb

Page 36

19.REPLACEMENT PARTS

TS 870 TRANSFER SWITCH

NOTE

There are no user serviceable components located on the TSC 80 printed circuit board. If the TSC 80 controller is deemed to be defective it must be returned to the Thomson Technology Factory for repair or replacement. Please refer to Product Return Policy section of this manual further information on product return procedures required.

19.REPLACEMENT PARTS

Replacement parts are available for the transfer switch as follows:

NOTE

When ordering replacement parts please provide the following information:

-Transfer Switch Model code (e.g. TS 873AA0200AS) -Transfer Switch Serial Number (e.g. W-022345)

The above information can be found on the transfer switch equipment rating plate located on the outside of the ATS door.

	Component Description	Thomson Technology	Comments
	Component Description	Part Number	Comments
		Part Number
	TSC 80 Service Replacement	TSC80SR	Must set configuration Jumper prior
	Controller Board c/w lexan		to use. Refer to TSC 80 Instruction
			Manual.

	TSC 80 Lexan Faceplate	005336	Contact Thomson Technology
			Service Dept for installation
			procedures.

	TSC 80 Rear Cover	005707

	Limit Switch 1 n/o, 1 n/c (all	004929	Must install and adjust for proper
	ATS Models)		operation before use. Contact
			Thomson Technology Service Dept
			for installation/adjustment
			procedures

	Transfer Switch Motor	007701	Motor is supplied with gear box

PM062 REV 5 08/05/05

32

Thomson Technology

Image 36

Technicolor - Thomson TS 870 Replacement Parts, Component Description, Thomson Technology, Comments, Part Number

Contents

AUTOMATIC TRANSFER SWITCHES INSTALLATION, OPERATING SERVICE MANUAL9087A - 198th Street, Langley, BC Canada V1M 3B1 Telephone 604 PM062 Rev 5 08/05/05Page TABLE OF CONTENTS NOTES TO INSTALLERGENERAL NOTES ON SERVICING TRANSFER SWITCH MECHANISM TRANSFER SWITCH MECHANISM - 100A-800A, S STYLETRANSFER SWITCH MECHANISM -1000A-1200A, T-STYLE RECOMMENDED MAINTENANCECONNECTION CONFIGURATION OPTIONS GROUND FAULT SITE TEST REQUIREMENTSOperating & Service Manual Version 1. PRODUCT REVISION HISTORY2. EQUIPMENT STORAGE to change without notice3. NOTES TO INSTALLER 3.1. UPSTREAM CIRCUIT PROTECTIVE DEVICES/ELECTRICAL CONNECTIONSDo not open equipment until ALL power sources are disconnected DANGER Arc Flash and Shock Hazard. Will cause severe injury or death3.2. TRANSFER SWITCHES WITH INTEGRAL OVER CURRENT PROTECTION 3.3. TRANSFER SWITCHES WITH MULTI-TAP VOLTAGE CAPABILITYcoordination. Failure to do so may result in equipment failure VOLTAGE ON TS870 SERIES TRANSFER SWITCHES WITH TSC 3.4. SYSTEM PHASING-HIGH LEG DELTA SYSTEMS3.5. REMOTE START CONTACT FIELD WIRING 3.6. DIELECTRIC TESTING3.7. INSTALLATION OF OPEN TYPE TRANSFER SWITCHES 4. GENERAL DESCRIPTIONUtility to indicate the source of primary power 4.1. PRODUCT MODEL CODE TS 870 TRANSFER SWITCHPM062 REV 5 08/05/05 Thomson Technology4.2. TYPICAL COMMISSIONING PROCEDURES 5.1. STANDARD AUTOMATIC TRANSFER SWITCH5. GENERAL THEORY OF OPERATION 5.1.1. NORMAL OPERATION5.2. SERVICE ENTRANCE AUTOMATIC TRANSFER SWITCH 5.2.1. NORMAL OPERATION5.2.2. OVER CURRENT TRIP 5.2.3. SERVICE DISCONNECT PROCEDURE Close and lock the transfer switch enclosure doorbefore connecting power sources 5.2.4. ADDITIONAL PROCEDURES Do not open equipment until ALL power sources are disconnectedDANGER Arc Flash and Shock Hazard. Will cause severe injury or death Failure to move the mechanism to the Neutral Position may result in serious personal injury or death due to electrical shock 6.1. STANDARD TS 870 AUTOMATIC TRANSFER SWITCH 6. OVER CURRENT PROTECTION5.3. TEST MODES Page 7. GENERAL NOTES ON SERVICING TRANSFER SWITCH MECHANISM Do not open equipment until ALL power sources are disconnectedDANGER Arc Flash and Shock Hazard. Will cause severe injury or death No moisture or other contamination is present 8. TRANSFER SWITCH MECHANISM - 100A-800A, S Style 8.1. MANUAL OPERATIONDo not open equipment until ALL power sources are disconnected DANGER Arc Flash and Shock Hazard. Will cause severe injury or deathAutomatic operation may be regained by replacing the control circuit isolation plug. With all sources of power de-energized to the transfer switch, the control circuit isolation plug can be re-connected. The drive system will operate the transfer switch to the required position. See manual operation instruction on front of transfer switch mechanism 9. TRANSFER SWITCH MECHANISM -1000A-1200A, T-Style 9.1. MANUAL OPERATIONDo not open equipment until ALL power sources are disconnected DANGER Arc Flash and Shock Hazard. Will cause severe injury or deathTS 870 TRANSFER SWITCH PM062 REV 5 08/05/05Thomson Technology 10. RECOMMENDED MAINTENANCE Do not open equipment until ALL power sources are disconnectedDANGER Arc Flash and Shock Hazard. Will cause severe injury or death TS 870 TRANSFER SWITCH PM062 REV 5 08/05/05Thomson Technology TS 870 TRANSFER SWITCH PM062 REV 5 08/05/05Thomson Technology TS 870 TRANSFER SWITCH PM062 REV 5 08/05/05Thomson Technology ØC ØB ØA NTS 870 TRANSFER SWITCH PM062 REV 5 08/05/05Thomson Technology 14. CONNECTION CONFIGURATION OPTIONS TS 870 TRANSFER SWITCHPM062 REV 5 08/05/05 Thomson Technology15. CABLE TERMINAL INFORMATION 16. REQUIREMENTS FOR UPSTREAM CIRCUIT PROTECTIVE DEVICES16.1. WITHSTAND CURRENT RATINGS ALL MODELS WITHOUT INTEGRAL TS 870 TRANSFER SWITCH17. GROUND FAULT SITE TEST REQUIREMENTS 16.2. INTERRUPTING CAPACITY CURRENT RATINGS ALL MODELS WITH17.1. PERFORMANCE TEST The interconnected system shall be evaluated to ensure compliance with the appropriate schematic drawings. The proper location of sensors and power cabling shall be determined. The grounding points of the system shall be verified to determine that ground paths do not exist that would bypass the sensors. The use of high-voltage testers and resistance bridges may be required. A simulated fault current is to be generated by a coil around the sensors. The reaction of the circuit-interrupting device is to be observed for correct response. The results of the test are to be recorded on the test form provided 18. TROUBLESHOOTING Do not open equipment until ALL power sources are disconnectedTS 870 TRANSFER SWITCH DANGER Arc Flash and Shock Hazard. Will cause severe injury or deathTS 870 TRANSFER SWITCH power failure in the utility sourcewhen it should No time delay when there should be19. REPLACEMENT PARTS Component DescriptionThomson Technology Comments20. PRODUCT RETURN POLICY Component DescriptionThomson Technology Comments21. NOTES TS 870 TRANSFER SWITCHPM062 REV 5 08/05/05 Thomson Technology22. PERFORMANCE TEST FORM Page TYPICAL AUTOMATIC TRANSFER SWITCH COMMISSIONING PROCEDURES Model Series TSAPPENDIX “A” Do not open equipment until ALL power sources are disconnectedFinal Commissioning TYPICAL AUTOMATIC TRANSFER SWITCHCOMMISSIONING PROCEDURES Model Series TS 2 Check for mechanical damage shipping or installerTYPICAL AUTOMATIC TRANSFER SWITCH COMMISSIONING PROCEDURES Model Series TSAPPENDIX “A” iii Green “Load” LED is “ON”TYPICAL AUTOMATIC TRANSFER SWITCH COMMISSIONING PROCEDURES Model Series TSAPPENDIX “A” 20 Ensure copies of manuals for the equipment are on siteSWITCHES WITH TSC 80 CONTROLLER APPENDIX “B”INSTRUCTIONS TO CHANGE SYSTEM VOLTAGE ON TS 870 SERIES TRANSFER Do not open equipment until ALL power sources are disconnectedSWITCHES WITH TSC 80 CONTROLLER APPENDIX “B”INSTRUCTIONS TO CHANGE SYSTEM VOLTAGE ON TS 870 SERIES TRANSFER 600V