GM863-GPS | Telit Wireless Solutions GE863-QUAD, GE863-PY instruction

GE863-QUAD

GE863-PY

1vv0300715 Rev. 1 - 19/09/06

	8				audio2.skd
12dBFS 16	EXTERNAL		16
-	EXTERNAL
	AMPLIFIER
Differential Line-OutDrivers		FullyDifferential PowerBuffers		Balanced	Single ended
GM863-GPS	EarMT+	MicMT-EarMT-	EarHF+		EarHF-
GM863-GPS	Mic MT+	MicMT-EarMT-	Mic HF+	Mic HF-
		rms	rms
		365mV	23mV		Paths
					Audio
		+20dB	+10dB
		3,3mVrms	0,33mV rms
		-45dBV/Pa	-45dBV/Pa
		7cm
			50cm

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved

page 31 of 79

Image 31

Telit Wireless Solutions GE863-QUAD, GE863-PY manual GM863-GPS

Contents

GE863-QUAD GE863-PY Hardware User Guide Contents 10.4 10.110.2 10.3 13.1 12.113.2 This document is relating to the following products Overview PIN-OUT GE863 module connections Pin Signal Function Internal Type Pull up Pin Signal Function Internal Type Pins Layout Turning on the GE863-QUAD/PY Hardware Commands Turning off of the device can be done in two ways Turning OFF the GE863-QUAD/PY Hardware shutdown Hardware Unconditional Reboot GE863-QUAD 1Power Supply Requirements Power SupplyGE863-QUAD/PY power requirements are Electrical design Guidelines 2General Design Rules An example of linear regulator with 5V input is 1.2 + 12V input Source Power Supply Design Guidelines An example of switching regulator with 12V input is Battery Source Power Supply Design Guidelines Battery Charge control Circuitry Design Guidelines Thermal Design Guidelines Power Supply PCB layout Guidelines GSM Antenna Requirements Antenna Serial Ports GSM Antenna installation GuidelinesGSM Antenna PCB line Guidelines Level Min Max Absolute Maximum Ratings -Not Functional Parameter Min Max Clear to Send Output from the GE863-QUAD/PY that Signals in the Uart connector on the EVK areNumber Pad Number 17-28-36 Ground 45-48-50-56 2MODEM Serial Port 2 Python Debug It is available on the following pins3RS232 level translation An example of level translation circuitry of this kind is 5V Uart level translation GE863-QUAD Audio Section Overview GM863-GPS + 20dB Microphone Paths Characteristic and RequirementsEcho canceller type Handset Echo canceller type Car kit hands-free You can set GA= +20dB to use standard resistor values That means TIP environment consideration Other considerations General Design Rules Balanced Microphone Biasing Microphone Biasing Unbalanced Microphone Biasing GE863-QUAD Buffered Balanced Mic Microphone BufferingSample circuit can be Buffer gain is given by the formula Gain = RR604605 = RR607606 Buffered Unbalanced Single Ended Microphone Buffer bandwidth at -3dB shall be 4KHz Freq . = 2π * R719* C726 2π * R711* C727 GE863-QUAD Short description Output Lines Speaker SW volume level step Number of SW volume steps Output Lines Characteristics Noise Filtering Handset Earphone Design An example of internal Ear amplifier could be Hands-Free Earphone Low Power Design Car Kit Speakerphone Design Short Description Evaluation Kit for Telit Modules EVK2 @ 350mW 2 EVK2 Audio Lines Characteristics ESD Data Integrity SIM Supply Schematic Layout Using a Gpio Pad as Output Using a Gpio Pad as InputGeneral Purpose I/O Using the Buzzer Output GPIO7 10.3Using the Alarm Output GPIO6 Min Max Units DAC and ADC section11.1DAC Converter Description Low Pass Filter Example An AT command is available to use the DAC functionCommand is AT#DAC=enable,value Enabling DAC Input Voltage range AD conversion Bits Resolution Using ADC Converter11.2ADC Converter Sensitivity Lux Camera12.1Transchip Camera Type Camera Interface Connectors Camera Physical Detail & Connector Camera Socket Connector Camera Board Module Main Block Diagram for supported cameras Schematic Diagrams for supported camera Example usage script for camera Camera setting shown here are the defaults onesTaking an reading a photo Mounting the GE863-QUAD / PY on the Application Board 13.2Module Finishing & Dimensions13.1General Lead-free Alloy Surface finishing Ni/Au for all test pads Recommended foot print for the application Stencil Debug of the GE863 in ProductionPCB pad Design Solder paste Following is the recommended solder reflow profile 13.2.6 GE863-QUAD / PY Solder Reflow GE863-QUAD Section A-A Packing System Modules orientation on tray Moisture Sensibility Conformity Assessment Issues Safety Recommandations 19/09/06 Document Change LogRevision Date Changes 21/02/06