Manuals / The Speaker Company / Computer Equipment / Label Maker

The Speaker Company ta200 manual Using RS-232 interface to setup Ethernet interface

Models: ta200

1 49

Download 49 pages 35.84 Kb

Page 40

Image 40

5.4.2Using RS-232 interface to setup Ethernet interface

1.Connect the computer and the printer with a RS-232 cable.

2.Turn on the printer power.

3. Start the Diagnostic Utility by double clicks on the

icon.

4.Select “COM” as interface then click on the “Setup” button to setup the serial port baud rate, parity check, data bits, stop bit and flow control parameters.

5.Click on the “Ethernet Setup” button from printer function of Printer Configuration tab to setup the IP address, subnet mask and the gateway for the on board Ethernet.

Page 40

Image 40

The Speaker Company ta200 manual Using RS-232 interface to setup Ethernet interface

Contents

TA200/ TA300 Series THERMAL TRANSFER / DIRECT THERMAL BAR CODE PRINTERUSER’S MANUAL Copyright Information Agency Compliance and Approvals CE CLASS A EN EN FCC CFR Title 47 Part 15 Subpart B ICES-003 Class A GB-4953GB9254 CLASS A GB27625 此为 A 级产品，在生活环境中，该产品可能会造成无线电干扰，在这种情况下，可能需要用户对干扰采取切实可行的措施。Contents Product Features1.2.1 Printer Standard Features 1.2.2 Printer Optional FeaturesStart the Diagnostic Tool 5.4.1 Using USB interface to setup Ethernet interface5.4.2 Using RS-232 interface to setup Ethernet interface 5.4.3 Using Ethernet interface to setup Ethernet interface1. Introduction 1.1 Product Introduction1.2 Product Features 1.2.1 Printer Standard FeaturesProduct standard feature 203 dpi1.2.2 Printer Optional Features Product option featureUser Dealer1.3 General Specifications 1.4 Print Specifications1.5 Ribbon Specifications General Specifications1.6 Media Specifications Media Specifications203 dpi models 300 dpi models2. Operations Overview 2.1 Unpacking and Inspection2.2 Printer Overview 2.2.1 Front View2.2.2 Interior View 2.2.3 Rear View Recommended micro SD card specificationSD card spec SD card capacity3. Setup 3.1 Setting up the Printer3.2 Loading the Ribbon 5. Insert the ribbon to the ribbon spindle Page  Ribbon loading path Please refer to videos on TSC YouTube or driver CDPrint head Ribbon3.3 Loading the Media 3.3.1 Loading the Roll LabelsGap sensor Media guide Black mark sensor Platen rollerPlease calibrate the gap/ black mark sensor when changing media  Media loading pathMedia bar Gap sensor Platen roller Black mark sensor Media Path for outside wound Path for inside wound Media guide3.3.2 Loading the Media in Peel-off mode Option Liner Label LinerPost-Print Action setting then click “Set” button to enable the peel-off mode3.3.3 Loading the Media in Cutter Mode Option 3.3.4 External Label Roll Mount Installation Option 1” label spindle 3” label spindlePlease calibrate the gap/black mark sensor when changing media 4. Feed the media through the rear external label entrance chute4.1 LED Indicator 4. LED and Button Functions4.2 Regular Button Functions LED Color4.3 Power-on Utilities 4.3.1 Ribbon and Gap/Black Mark Sensor Calibration4.3.2 Gap/Black Mark Calibration, Self-test and Dump Mode Self-test printout  Self-testSelf-test printout with printer firmware V7.0 and later version Print speed inch/sec Print darkness Label size inch Gap distance inch 4.3.3 Printer Initialization  Dump mode4.3.5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor Default settingParameter 4.3.6 Skip AUTO.BAS 5. Diagnostic Tool 5.1 Start the Diagnostic Tool5.2 Printer Function 2. Click the “Printer Function” button to setup1. Select the PC interface connected with bar code printer Function5.3 Calibrating Media Sensor by Diagnostic Tool 5.3.1 Auto Calibration5.4 Setting Ethernet by Diagnostic Utility Option 5.4.1 Using USB interface to setup Ethernet interface5.4.2 Using RS-232 interface to setup Ethernet interface 5.4.3 Using Ethernet interface to setup Ethernet interface Factory Default button 6. Troubleshooting 6.1 Common ProblemsProblem Recovery ProcedureNot Printing FLASH / DRAMmicroSD card is unable to Poor Print QualityThe printing position of small label is incorrectMissing printing on the left or RTC time is incorrect when7. Maintenance 2. The cleaning process is described as following Lint-free cloth  Vacuum / Blower brush  100% ethanol Printer PartContent Revise HistoryDate EditorPage Corporate Headquarters