Thermador PRDS48, PRDS36, PRG304, PRDS304 installation instructions Cabinet Clearances, Wan

STEP 2: CABINET PREPARATION

1.The range is a free standing unit. If the unit is to be placed adjacent to cabinets, the clearances shown in Fig. 1 are required. The same clearances apply to island installations, except for the overhead cabi

4.The maximum depth of over head cabinets installed on either side of the hood is 13".

5.Any openings in the wall behind the range and in the floor under the range must be sealed.

required for each type of backguard.

7.Always keep appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

nets, which must have a space	6. When there is less than a 12"		8. Do not obstruct the flow of
wide enough to accept the	horizontal clearance between		combustion and ventilation air
flared island hood, as indicated	combustible material A and the		to the unit.
in Fig. 1.	back edge of the range above		CAUTION:
	the cooking surface, a
2. The PRDS48 Ranges must be
	Thermador Low Back or High
placed with the oven door			Do not install the iModel
	Shelf backguard must be
projecting out from the cabinet			PRDS48 ranges such that the
	installed. (See Fig. 2a). When
face. The cabinet face should			oven door is flush with the
	clearance to combustible
line up with the oven front			cabinet face. A flush installa
	material A is over 12", a
frame, which is the surface that			tion could result in damage to
	Thermador Island Trim may be
the oven door closes against.			the cabinets due to exposure
	used. (See Fig. 2b). Except in
(See Fig. 2b and 2c illustrating			to high heat.
	the case of 30" Ranges,
side views of 48" ranges.)
	backguards must be ordered		A As defined in the "Nationa\ Fue\
3. The gas and electrical supply	separately. Figures 2a. 2b		Gas Code" (ANSI Z223.1. Latest
should be within the zones	and 2c indicate the space		Edition).
shown in Fig. 3a, 3b and 3c.
FIG. 1 Cabinet Clearances	30" Wide Hood (Model *PH30QS)	I For 30' Ranges
	48" for Island (Model #PHI48QS)

36" Wide Hood (Model #PH36QS) j For 36" Rangej 48" for Island (Model #PHI48QS)

48" Wide Hood (Model 0PH48QS) For 48' Ranges' 60" for Island (Model #PHI60QS)

Min. Distance Between Overheaad -4-»»

Cabinets of Combustible MaterialalA I

		30" Range - 30"
		36" Range - 36"	13"M
			Cabinet
		48" Range - 48"
			Depth		CAUTION: See
	30" Min. to 36" Max.	Range width	12' Mn to		Figs. 2a	2b and
	bottom of overhead	30". 36" or 48"			2c 42'	Min to
			combus
	Hood to cooking				combustible
			tible side
	surface (42" if hood
			wan	"'	material A.
	contains combustible
18" Min.			cii	.A	from cooking
	materials A)		(bom		surface

sees!

For Electrical and Gas Supply Zone, "see Figures 3a, 3b and 3c. Zone size and position differ according to the model.

•35-3/8" Min. Range Height with

Leveling Legs fully retracted	A as defined in the "National Fuel Gas Code" (ANSI Z223.7. Latest
•36-3/4" Max. Range Height with	Edition). 'The range height is adjustable. The level of the range top
Leveling Legs fully extended	must be at the same level or above the countertop level.
	Page 4