Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-880-QQ SERIES owner manual Cleaning the Cutter Unit, Cleaning the strip unit

Models: B-880-QQ SERIES

1 34

Download 34 pages 42.69 Kb

Page 27

■Cleaning the Cutter Unit

11. GENERAL MAINTENANCE

EO1-33017

11.4 REMOVING JAMMED MEDIA

■Cleaning the Cutter Unit

WARNING!

1.Be sure to turn the power off before cleaning the cutter unit.

2.The cutters are sharp and care should be taken not to injure yourself when cleaning.

1.Loosen two screws and remove the cutter cover.

2.Remove the white screw and media guide.

3.Remove the jammed paper and trash.

4.Clean the cutter with dry cloth.

Screw

White Screw	Media Guide

Cutter Cover

Swing Cutter

5. Assembling is reverse order of removal.

■Cleaning the strip unit

WARNING!

Fixed Cutter

Cutter Unit

Fig. 11-7

Be sure to turn the power off before cleaning the strip unit.

1.Lower the backing paper release bar to remove the jammed media.

2.Clean the strip roller and backing paper holder with ethyl alcohol.

Strip Roller

Backing Paper Holder

Backing Paper Release Bar

Fig. 11-8

11-5

Image 27

Toshiba B-880-QQ SERIES owner manual Cleaning the Cutter Unit, Cleaning the strip unit

Contents

B-880-QQ SERIES Owner’s ManualTEC Thermal Printer for USA only Safety Summary Meanings of Each SymbolSafety Summary Precautions Request Regarding MaintenanceSafety Summary TABLE OF CONTENTS B - 8 8 2 - T S 1 0 - Q Q 1.2 ACCESSORIES1. INTRODUCTION 1.1 APPLICABLE MODEL2.1 PRINTER 2. SPECIFICATIONSAuto Ribbon Saving Mode 2.2 OPTIONMEDIA 2.4 RIBBON2. SPECIFICATIONS POWER LED Green 3. OVERVIEW3.1 FRONT/REAR VIEW 3.2 OPERATION PANELThe media sensor position is selected 4. PARAMETER SETTING FUNCTIONSParameter Setting Mode Table 4. PARAMETER SETTING FUNCTIONS5. SET UP PROCEDURE 5.2 SETTING UP THE PRINTER5.1 REQUIREMENTS FOR OPERATION 6. INSTALLATION PROCEDURE 6. INSTALLATION PROCEDURE6.1 CONNECTING THE POWER CORD AND CABLES 6.2 HOLDER STAND INSTALLATIONHead Lever Position 7. LOADING THE RIBBON8. Set the head lock plate 8. LOADING THE MEDIA 8. LOADING THE MEDIA5. Turn the Lock Levers of the Media Holders to the unlock position and readjust the Media position to the center. Then lock the Media Holders securely with the Lock Levers. Fit the Media Guides to the Media. Tighten the screw A firmly An easy way to set the black mark sensor position Setting the feed gap sensor positionFeed Gap Sensor Black Mark Sensor Adjusting Knob Black Mark Media Black Mark Sensor Feed Gap Sensor Adjusting Knob Media8. The media is now loaded and the sensor position is set. Batch type Media Backing Paper Backing Paper Release Bar Backing Paper Holder 9. INSERTING THE OPTIONAL PCMCIA CARD 1. Turn the power off3. Turn the power on 10. CARE/HANDLING OF THE MEDIA AND RIBBON 10. CARE/HANDLING OF THE MEDIA AND RIBBON11.1 CLEANING 11. GENERAL MAINTENANCE7. Turn the pinch roller lever to the right 11.3 COVERS AND PANELS 11.2 UNDER THE MEDIA GUIDES11.4 REMOVING JAMMED MEDIA Cleaning the strip unit Cleaning the Cutter Unit11.5 THRESHOLD SETTING Threshold setting procedure11. GENERAL MAINTENANCE Solution 12. TROUBLESHOOTINGError Message ProblemError Message ProblemSolution Problem Error MessageProblem SolutionPage Page PRINTED IN JAPAN EO1-33017