2. SPECIFICATIONS
2.3 MEDIA
2.3 | MEDIA |
|
|
| |
|
|
|
| Label | |
| Stop | I |
|
|
|
|
|
|
|
| |
| position |
|
|
|
|
| Cut |
|
|
|
|
| position |
|
|
|
|
|
| J |
| Reference |
|
|
|
| H | coordinate | 1 |
|
|
|
|
| |
|
|
|
| Reference |
|
|
|
|
| coordinate | 2 |
|
|
|
| G |
|
|
|
|
| D |
|
|
|
|
| C |
|
Refer to the following |
|
|
|
NOTE 2. |
|
|
|
Black Mark |
| Tag paper | Black Mark |
(on reverse side) | I |
| (on reverse side) |
Stop |
| Tag paper | |
|
| ||
position |
|
|
|
E | F |
| Cut |
| position |
| Reference |
|
A | coordinate 1 | A |
B | H |
|
| Reference |
|
| coordinate | 2 |
Feed direction
G
C
Fig.
[Unit: mm]
Label dispensing mode
Item
A : Span of one label/tag
B : | Label length |
| |
C : | Width including backing paper | ||
D : | Label width |
| |
E : | Gap length |
| |
F : | Black mark length (Tag paper) | ||
G : | Effective print width | ||
H : |
| Label | Standard |
Effective |
| ||
|
| ||
print length | Tag | Standard | |
|
|
|
I : Print speed up/slow down area
J : Black mark length (Label)
Maximum effective Standard length for on the fly issue
Outer roll diameter
Label
Thickness Tag
Batch mode | Strip mode | Cut mode | |||
10.00 ~ 1368.0 | 25.4 ~ 1368.0 | Label: 38 ~ 1368.0 | |||
Tag: 25.4 ~ 1368.0 | |||||
|
|
| |||
7.5 ~ 1366.0 | 22.9 | ~ 1366.0 | 25.0 ~ 1362.0 | ||
| 101.6 ~ 225.0 |
|
| ||
| 98.6 | ~ 222.0 |
|
| |
2.5 ~ 20.0 | 2.5 | ~ 20.0 | 6.0 | ~ 20.0 | |
| 2.5 | ~ 10.0 |
|
| |
| 10.0 | ~ 213.3 |
|
| |
5.5 ~ 1364.0 | 20.9 | ~ 1364.0 | 23.0 | ~ 1364.0 | |
8.0 ~ 1364.0 |
| 23.4 | ~ 1364.0 |
1.0
Refer to the following NOTE 2.
682.0
Ø200 Max.
0.13~ 0.17
0.10~ 0.17
NOTES: 1. The media specification other than above are unchanged.
2.When marking black marks on label rolls, the following requirements must be satisfied. When the gap length is less than 4 mm:
The black mark length should be longer than the gap length. When the gap length is 4 mm or more:
The black mark should not overlap the gap for more than 4 mm and the following label.
3.When issuing thermal labels at 8"/sec., the print stop position should be set to a minimum of 1 mm inside the label.
2.4 RIBBON
Type | Spool type |
|
|
Width | 115 mm ~ 224 mm |
|
|
Length | 300 m |
|
|
Outer diameter | Ø72 mm (max.) |
|
|
NOTES: 1. “On the fly issue” means that the printer can draw and print without stopping between labels.
2.To ensure print quality and print head life use only TOSHIBA TEC specified media and ribbons.
3.When using the cutter ensure that label length B plus inter label gap length E exceeds 35 mm. (i.e. label pitch should be greater than 35 mm.)
4.Use of rough media for the ribbon saving issue may cause ribbon smudges.
5.To avoid ribbon wrinkles use the ribbon which is wider than media by 5mm or more. However, too much difference in width between the two may cause wrinkles.