Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SV4T owner manual Connecting the Power Adapter and the Power Cord

Models: B-SV4T

1 42

Download 42 pages 56.26 Kb

Page 15

2.5Connecting the Power Adapter and the Power Cord

2. PRINTER SETUP

ENGLISH VERSION EO1-33062

2.5 Connecting the Power Adapter and the Power Cord

2.5Connecting the Power Adapter and the Power Cord

NOTES:

1.Since the power cord is not enclosed in this printer, please purchase a proper one after referring to page 1-2.

2.The EA10953 AC adapter should be exclusively used for the B-SV4T Series printer. The B-SV4T Series printer must be powered by the EA10953 AC adapter.

1.Make sure that the printer power switch is in the OFF (O) position.

2.Insert the Power Cord into the inlet of the Power Adapter.

Power Cord				Power Adapter

3.Insert the Power Adapter connector into the Power Jack on the rear of the printer.

Power Jack

Power Adapter

Connector

4.Plug the other end of the Power Cord into a grounded outlet as shown in the figure below.

E2- 4

Image 15

Toshiba B-SV4T owner manual Connecting the Power Adapter and the Power Cord

Contents

TOSHIBA Barcode Printer B-SV4T SERIESB-SV4T SERIES Owner’s ManualTOSHIBA Barcode Printer Waste Recycling information for users N258CE Compliance for EU only VORSICHTMeanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsPRODUCT OVERVIEW TABLE OF CONTENTSMAINTENANCE APPENDIX 1 SPECIFICATIONSAPPENDIX 2 INTERFACE EA2-1GLOSSARIES INDEX 1.2 Features 1.3 Unpacking 1.4 Accessories 1. PRODUCT OVERVIEW1.1 Introduction When purchasing the power cord As of September1. PRODUCT OVERVIEW 1.5.2 Front View DimensionsAppearance 1.5.11.5.5 Button and Indicator Lamp 1.5.4 InteriorCaution Symbol for the Print Head Please refer to WARNING 2.1 Precautions 2. PRINTER SETUP2.2 Procedure before Operation 2.3 Turning the Printer ON/OFF2.3.1 Turning ON the Printer 2.4 Connecting the Cables to the Printer 2.3.2 Turning OFF the Printerc d e f 2.5 Connecting the Power Adapter and the Power Cord To open the Top Cover 2.6 Opening/Closing the Top CoverTo close the Top Cover 2.6 Opening/Closing the Top Cover Cont2.7 Loading the Media 2.7 Loading the Media Cont Batch mode 2.7 Loading the Media ContHow to set the media 2.7 Loading the Media ContStrip mode Option Cut mode Option When the Cutter is installed, the media is automatically cut2. PRINTER SETUP 2.7 Loading the Media Cont4. Manually move the Rear Media Guides so that the media is centred 2.7 Loading the Media Cont2.8 Loading the Ribbon 2.8 Loading the Ribbon Cont 2.9.2 Self Print Test and Dump Mode 2.9 Media SensorTest, and Dump Mode different type Utilities 2.9.1 Media Sensor CalibrationPrint test label sample 2.9.2 Self Print Test and Dump Mode ContThe following commands should not affect the test print issue 2. PRINTER SETUP3. MAINTENANCE 3.1 Cleaning3.1.1 Print Head Wipe the Platen with a soft cloth moistened with absolute alcohol 3.1.2 Platen/Sensors3.1.3 Cover 3. MAINTENANCEENGLISH VERSION EO1-33062 3.2 Care/Handling of the Media and Ribbon 3.2 Care/Handling of the Media and RibbonProblems 4. TROUBLESHOOTING4.1 Troubleshooting Guide 4.2 Removing Jammed MediaAPPENDIX 1 SPECIFICATIONS A1.1 PrinterSpecifications Option Name A1.2 OptionsA1.3 Media A1.3.1 Media TypeA1.3.1 Media Type Cont A1.3.2 Detection Area of the Transmissive SensorUnit mm inch A1.3.3 Detection Area of the Reflective Sensor Black MarkRectangular/Oval Hole A1.3.4 Effective Print Area A1.4 RibbonAPPENDIX 2 INTERFACE Interface CablesRS-232C Cable description GLOSSARIES Supply Thermal print headThermal transfer printing INDEX INDEX EO1-33062