Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SV4T owner manual Platen/Sensors, Cover, Maintenance

Models: B-SV4T

1 42

Download 42 pages 56.26 Kb

Page 29

3.1.2 Platen/Sensors

3. MAINTENANCE

ENGLISH VERSION EO1-33062

3.1 Cleaning

3.1.2 Platen/Sensors	1.	Wipe the Platen with a soft cloth moistened with absolute alcohol.
	2.	Remove dust or paper particles from the Black Mark Sensor, Feed Gap

Sensor, and Ribbon Sensor using an air blower.

Feed Gap Sensor

Black Mark Sensor

Platen

Ribbon Sensor

3.1.3 Cover

CAUTION!

Do not use any volatile solvents including thinner and benzene, as this may cause discoloration or distortion of the cover.

Wipe the Cover with a dry soft cloth. Wipe off dirt with a soft cloth slightly moistened with water.

E3- 2

Image 29

Toshiba B-SV4T Platen/Sensors, Cover, Wipe the Platen with a soft cloth moistened with absolute alcohol, Maintenance

Contents

TOSHIBA Barcode Printer B-SV4T SERIESTOSHIBA Barcode Printer B-SV4T SERIESOwner’s Manual CE Compliance for EU only N258VORSICHT Waste Recycling information for usersMeanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsMAINTENANCE TABLE OF CONTENTSAPPENDIX 1 SPECIFICATIONS PRODUCT OVERVIEWGLOSSARIES INDEX APPENDIX 2 INTERFACEEA2-1 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories1. PRODUCT OVERVIEW 1. PRODUCT OVERVIEW When purchasing the power cordAs of September Appearance Dimensions1.5.1 1.5.2 Front ViewCaution Symbol for the Print Head Please refer to WARNING 1.5.5 Button and Indicator Lamp1.5.4 Interior 2.1 Precautions 2. PRINTER SETUP2.3.1 Turning ON the Printer 2.2 Procedure before Operation2.3 Turning the Printer ON/OFF c d e f 2.4 Connecting the Cables to the Printer2.3.2 Turning OFF the Printer 2.5 Connecting the Power Adapter and the Power Cord To open the Top Cover 2.6 Opening/Closing the Top CoverTo close the Top Cover 2.6 Opening/Closing the Top Cover Cont2.7 Loading the Media 2.7 Loading the Media Cont 2.7 Loading the Media Cont Batch mode2.7 Loading the Media Cont Strip mode OptionHow to set the media When the Cutter is installed, the media is automatically cut Cut mode Option2. PRINTER SETUP 2.7 Loading the Media Cont4. Manually move the Rear Media Guides so that the media is centred 2.7 Loading the Media Cont2.8 Loading the Ribbon 2.8 Loading the Ribbon Cont 2.9.2 Self Print Test and Dump Mode Test, and Dump Mode different type Utilities2.9 Media Sensor 2.9.1 Media Sensor CalibrationThe following commands should not affect the test print issue 2.9.2 Self Print Test and Dump Mode Cont2. PRINTER SETUP Print test label sample3.1.1 Print Head 3. MAINTENANCE3.1 Cleaning 3.1.3 Cover 3.1.2 Platen/Sensors3. MAINTENANCE Wipe the Platen with a soft cloth moistened with absolute alcoholENGLISH VERSION EO1-33062 3.2 Care/Handling of the Media and Ribbon 3.2 Care/Handling of the Media and Ribbon4.1 Troubleshooting Guide 4. TROUBLESHOOTING4.2 Removing Jammed Media ProblemsSpecifications APPENDIX 1 SPECIFICATIONSA1.1 Printer A1.3 Media A1.2 OptionsA1.3.1 Media Type Option NameUnit mm inch A1.3.1 Media Type ContA1.3.2 Detection Area of the Transmissive Sensor Rectangular/Oval Hole A1.3.3 Detection Area of the Reflective SensorBlack Mark A1.3.4 Effective Print Area A1.4 RibbonRS-232C Cable description APPENDIX 2 INTERFACEInterface Cables GLOSSARIES Thermal transfer printing SupplyThermal print head INDEX INDEX EO1-33062