Toshiba Quality is Second to None | Toshiba e-STUDIO203 specs

TOSHIBA Quality is Second to None

Recommended toner cartridges

To assure optimal printing performance, we recommend that you use TOSHIBA toner cartridges.

If you use a TOSHIBA-recommended toner cartridge, you can utilize the following two check functions of this equipment:

Cartridge detecting function:

This function checks if the toner cartridge is correctly installed and notifies you if it is not.

Toner remaining check function:

This function notifies you when there is little toner remaining in the cartridge.

Any copying or printing operation is available even if you are using a toner cartridge other than the one we recommend. In that case, however, the equipment cannot detect whether the toner cartridge is installed or not and therefore the toner lamp is lit even if the toner cartridge is cor- rectly installed. You cannot utilize the toner remaining check function either.

If you are using a toner cartridge other than the one we recommend and you feel annoyed by this lighting lamp, contact your service representative. Your service technician will cancel the cartridge detecting function set by default. Remember once this function has been cancelled, you will not be able to utilize the two functions mentioned above even if you change the cartridge to the one we recommend.

TOSHIBA Quality is Second to None 11

Image 13

Toshiba e-STUDIO203 manual Toshiba Quality is Second to None, Recommended toner cartridges, Cartridge detecting function

Contents

Operators Manual for Copying Functions EPA Energy Star MFD For Germany only For EU onlyPage Operator’s Manual for Copying Functions Lineup of Our Manuals Before Reading This Manual Precautions in this manual Trademarks Description of original/paper direction Before Reading This Manual Contents 100 Copying in Same Page Order as Originals Sort Copying Index 111 Contents Recommended toner cartridges Toshiba Quality is Second to NoneCartridge detecting function Toner remaining check function Toner Supplies / PartsGeneral Functions extended by various options Features of e-STUDIO163/203Ecological energy-saving design When installing or moving General Precautions 10 cm 80 cm Other points When using the equipment Position of Certification label, etc When handling supplies During maintenance or inspection Poration Disclaimer Notice Disclaimer Notice Description of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Front / Right side Description of Each ComponentPlaten Cover Automatic Document Feeder optional, MR-2017 Left side / Inner side Receiving tray Scanning area USB terminal 4-pinOriginal scale Platen sheet Configuration of options Control panel Density adjustment buttons/lamps Original mode button/lampsLED display Copy qty. / zoom display selecting button/lamp Drawer button/lamps Original setting lampCopy button/lamps Original button/lamps Turning power on Preparation 1 Turning Power onTurning power OFF To turn the equipment into the energy saving mode manually Saving energy when not in use Energy saving modeCancelling the energy saving mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Paper types not acceptable Recommended paperStoring paper Media type Product name Press down the paper plate Placing paper in drawers Widen the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper size Register the paper size into the equipment Do not let your fingers be caught when closing the drawer Registering standard size A3, A4, A4-R, A5-R, B4 Preparation 3 Registering Size of Paper Placed Code No Registering other standard sizes Preparation 3 Registering Size of Paper Placed Press the Start button Placing Originals Using Bypass TrayMaking Copies Setting position Type of origi When the built-in memory has become full during scanningPlacing Originals Acceptable originals Placing originals on the original glass Placing booklet-type originals such as books or catalogues Precautions for Automatic Document Feeder optional Using Automatic Document Feeder optionalWhen black streaks appear on the copied image Maximum number Paper weight Placing originals on Automatic Document Feeder optional When placing a large amount of originals with a long width Check if paper is placed in the drawer Making CopiesPlace the original Select the copy modes as required When the paper has run out When the number of sheets exiting has exceededStopping/Resuming copying Press the CLEAR/STOP button during scanning or copying Press the Interrupt button Interrupting copying and making another copy Interrupt copy Media type Paper size Maximum sheet Capacity *1 Using Bypass Tray Preparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Using Bypass Tray Zooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Contents Default setting at installation Default Settings Automatic paper selection APS Paper SelectionPlace the original on the Automatic Document Feeder Automatic paper selection APS Place paper in the drawer Place the original Manual paper selection Selecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manually If the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Press Zooming out or Specifying reproduction ratio manuallyDesired reproduction ratio appears Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode To adjust the density to the desired level Adjusting Density LevelTo return it to the automatic copy density mode Dark Adjusting Density Level Settings and Management Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/Off Checking Total Number Copied Switch the display to check the rest of the total numberPress Button for more than two seconds Checking Total Number Copied When Message Lamp is Lit/Blinking Paper Jams Troubleshooting Cover open lamp When Message Lamp is Lit/BlinkingPaper empty lamp Toner lamp Recommended toner cartridges Paper jam lamp Service call lamp Paper Jams When paper jams occur frequentlyChecking position of paper jams Paper jams within Automatic Document Feeder optional When releasing jammed paperRaise the lever, and then open the upper cover Do not tear jammed paper Paper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass tray Paper jam behind transfer unit Close the transfer unit and the side cover Open the transport guide while holding the knob a Paper jams within fuser unit Release the jammed paper Paper jams within Paper Feed Unit optional Open the front cover Replacing Toner CartridgeHold down the green lever Pull out the toner cartridge Insert the toner cartridge along the rail Clean the chargerOpen the side cover With the transfer charger wire Equipment starts supplying toner General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Original/Copy paper-related items Toner-related items Image trouble Tion Charger is dirty Clean the charger Daily Inspection 100 Maintenance and Inspection Original glass Guides Platen sheet Daily Inspection Open the front cover Clean the charger Cleaning charger Cleaning transfer charger Daily Inspection Daily Inspection Specifications and Options OPC STUDIO163/203 Specifications Paper size Feeder STUDIO163 STUDIO203 Continuous copying speed Automatic Document Feeder Specifications of OptionsPaper Feed Unit Packing List Packing List AMS APS Index 106 DP-1640/2030 OME050129B0 Multifunctional Digital Systems